User manual FENDER CYBER-TWIN SE

[. . . ] 2 Fender ® Cyber­Twin ® SE Amplifier A PRODUCT OF: FENDER MUSICAL INSTRUMENTS CORPORATION CORONA, CA USA Copyright ©2004 by FMIC Trademarks Fender®, Cyber­Twin®, Telecaster®, Stratocaster®, BlackfaceTM, Dyna­TouchTM, Mr. GearheadTM, Virtual Tone InterpolationTM, Hot RodTM, Bassman®, Deluxe Reverb®, Princeton®, Twin Reverb®, Innovate. . . Don't Emulate® and all related logos are trademarks or registered trademarks of FMIC. Other trademarks are property of their respective owners. w w w. f e n d e r. com w w w. m r g e a r h e a d . net Fender ® ®Cyber­Twin ® ®SE Amplifier Fender Cyber­Twin SE Amplifier 3 Important Safety Instructions · This symbol warns the user of dangerous voltage levels localized within the enclosure of the unit. · This symbol advises the user to read all accompanying literature for safe operation of the unit. · Read, retain, and follow all instructions. [. . . ] Gated--Unique modern Reverb, see Reverb Tone/Shape menu below. Fender Reverb--classic 1963 tube driven unit uniquely located predistortion, see Reverb In Level/Dwell menu below. REVERB TYPE Values: Small Room Plate Large Plate Reverb Large Room Small Hall Blackface Reverb Gated Large Hall Arena Small Small Ambience Fender Adjusts the Reverb circuit input level rather than the output level (which is controlled by the front panel REVERB knob). If Fender Reverb is the active Reverb type, this parameter is called Reverb Dwell. REVERB IN LEVEL / DWELL Values: 1. 0 (minimum) 10. 0 (maximum) w w w. f e n d e r. com w w w. m r g e a r h e a d . net Amp Edit Mode 15 Adjusts the Reverb high­frequency tone. Or, if Gated Reverb is active, this parameter adjusts Reverb Shape with which radical decay characteristics can be achieved such as rectangular, linear and reverse tails. REVERB TONE / SHAPE Values: 1. 0 (minimum) 10. 0 (maximum) Adjusts the Reverb sustain time. REVERB TIME Values: 1. 0 (shortest) 10. 0 (longest) Adjusts the Reverb decay from a sparse/irregular sound to a dense/smooth sound. REVERB DIFFUSION Values: 1. 0 (sparse) 10. 0 (dense) Shifts the equalization of the amplifier providing instant tone shaping to accommodate playing styles or to compensate for different room acoustics. TIMBRE Values: None Full Body Razor Edge Bright & Light Scoop Super Bright Squawk Acoustic Scoop Bass Booster Drop Selects the phase polarity (push/pull or pull/push) for each speaker. Fender amps with Reverb have traditionally had speakers operating in reverse polarity due to the extra tube gain stage necessary for Reverb. Useful when experimenting with stereo mike placement in the studio. SPEAKER PHASE Values: Both Standard Both Reverse Left Reverse Right Reverse Use to compress (moderate) the range of volume output due to extremes between soft and loud guitar playing intensities. Compression also provides sustain and is a fundamental component of many amplifiers. COMPRESSION Values: Off Low Medium High Even Higher Use to set the frequency cut­off boundary for the noisegate when it is activated. NOISEGATE DEPTH Values: 1. 0 10. 0 Use to set the signal level sensitivity for activating the noisegate. NOISEGATE THRESHOLD Values: Low Medium High Assigns a parameter to be controlled by an expression pedal (optional). Parameters in [brackets] appear only when a particular effect or Reverb is active. For a list of effects parameters, see page 16, for Reverb parameters, see above. EXPRESSION PEDAL ASSIGNMENT Values: Volume Gain Treble Middle Bass Presence Reverb [FX Level] [FX Val 1] [FX Val 2] [FX Val 3] [FX Val 4] Master Volume Reverb In Level [Dwell] Reverb Tone [Shape] Reverb Time Reverb Diffusion Assigns a parameter to be controlled by a MIDI continuous controller pedal (optional). Parameters in [brackets] appear only when a particular effect or Reverb is active. For effects types/parameters, see page16, for Reverb types/parameters, see above. CONTROLLER ASSIGNMENT Values: Volume Gain Treble Middle Bass Presence Reverb [FX Level] [FX Val 1] [FX Val 2] [FX Val 3] [FX Val 4] Master Volume Reverb In Level [Dwell] Reverb Tone [Shape] Reverb Time Reverb Diffusion Use to bypass the in or out signals for Reverb "tail" and/or effects. Or, when Vibratone is the active effect, the Rotor Speed Fast/Slow parameter is available for switching between two (adjustable) rotor speeds (see Vibratone, page 20). REVERB / FX BYPASS Values: FX In Reverb In Out FX Out & Reverb In FX Out Reverb Out FX & Reverb In FX In & Reverb FX & Reverb Out [Rotor Speed Fast/Slow] w w w. f e n d e r. com w w w. [. . . ] Make sure MASTER, TRIM, GAIN, VOLUME, TREBLE, MIDDLE, BASS and guitar are all above "1. " Make sure nothing is plugged into the HEADPHONE jack. Make sure Memory Protection is disabled in Utility Mode. Turn Trim down if the red LED is constantly on while playing. Press the FX button and if "None" is displayed, rotate the data wheel to select an effect. [. . . ]