User manual FENDER PREFIX PRO

[. . . ] U SER ' S G UIDE PREFIX TM PRO F ISHMAN P REFIX TMP RO This fine instrument is equipped with a FISHMAN PREFIXTM PRO ACOUSTIC GUITAR SYSTEM. Please read these instructions carefully. [. . . ] Doing so will prevent loudspeaker damage. BATTERY LOW LED When plugging into the endpin jack, the LOW BATTERY light will flash momentarily, indicating that the power is on. When the LOW BATTERY light stays on, it is time to change the battery. 3 F ISHMAN P REFIX TMP RO CONTROLS NOTCH FILTER This is a fixed level, variable-frequency filter for eliminating feedback or unwanted resonance. The affected frequency is variable from 40 to 500 Hz. The NOTCH FILTER is effectively off in the full counter-clockwise position. VOLUME CONTROL The Volume control goes from very quiet to very loud. BASS, & TREBLE CONTROLS These are boost/cut shelving tone controls. The center detent yields a flat response. MIDDLE & BRILLIANCE CONTROL These are resonant style boost/cut filters. When boosted, the BRILLIANCE control can add presence to your sound or brighten up dead strings. When cut, the MIDDLE control "scoops" out harsh midrange frequencies. PHASE SWITCH The PHASE switch compensates for acoustic phase differences that often occur between instrument and speaker. It can be used as a tone filter at low volume levels or a feedback filter at high levels. The PHASE switch can correct any electrical phase difference between the PREFIX PRO system and an outboard instrument microphone. Flip the PHASE switch several times and use your ear to find the optimum setting. The best position for the PHASE switch may change, depending on the sound system and/or venue acoustics. 4 A COUSTIC G UITAR S YSTEM SUGGESTED EQ SETTINGS These settings are meant to be used as a starting point for building your sound. MID CUT This is a good all-around setting. You can also cut midrange by boosting the BASS and TREBLE sliders to realize an implied mid-cut at 800 Hz. BRILLIANCE If you are playing through a guitar amplifier or have dead strings on the instrument, you can brighten up your sound with this setting. 5 F ISHMAN P REFIX TMP RO SUGGESTED EQ SETTINGS, CONTINUED CUT THROUGH THE MIX For cutting through a live band mix at high volumes. FINGERSTYLE This setting will add fullness to the bass and definition to the treble. 6 A COUSTIC G UITAR S YSTEM SPECIFICATIONS Nominal Input Level: Input Overload: Input Impedance: Output Impedance: Nominal Output Level: THD: Signal to Noise Ratio: -20 dBV (20 Hz - 20 kHz) +2 dBV 20 M Ohms Less than 3. 5 k Ohms -12 dBV Less than . 04 %, -20 dBV input 77 dB (A weighted referred to nominal -20 dBV input) Less than 3. 5 mA 9V Alkaline battery (estimated 160 hours continuous use with low battery indicator at 6. 5V) 40Hz - 500 Hz (-15 dB) ± 12 dB at 60 Hz ± 3 dB at 350 Hz ± 12 dB at 10 kHz ± 3 dB at 2. 4 kHz ± 12 dB at 1 kHz ± 3 dB Bandwidth 1. 1 kHz ± 12 dB at 10 kHz ± 3 dB Bandwidth 7 kHz Current Drain: Power Supply: Notch Filter Range: Bass Control Range: Treble Control Range: Mid Control Range: Brilliance Control Range: All specifications subject to change without notice. PREFIX TM PRO 7 L IMITED W ARRANTY INSTALLATION BY A QUALIFIED PROFESSIONAL REPAIRMAN IS STRONGLY RECOMMENDED. [. . . ] Warranty repairs or replacements will be sent automatically free of charge. If FISHMAN TRANSDUCERS determines the item is not covered by warranty, we will notify you of the repair or replacement cost and wait for your authorization to proceed. FISHMAN TRANSDUCERS® 340-D Fordham Road Wilmington MA 01887 USA Phone 978-988-9199 · Fax 978-988-0770 www. fishman. com 009-089-003 5-99 [. . . ]