User manual FERGUSON TE-D20 SERVICE MANUAL

[. . . ] FERGUSON TECHNIK AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTAL DAMAGES IRRESPECTIVE OF WHETHER FERGUSON TECHNIK OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES. Page 3 Reference Manual TE-D20 Version 2. 0 Regulatory information Europe Declaration of Conformity We FERGUSON Technik AG Brunnenweg 3 D-64331 Weiterstadt Germany Declare under our sole responsibility that the product TYPE: TE-D20 To which this declaration relates is in conformity with the following standards (environments E1-E3): EN 55103-1 /1996 EN 55103-2 /1996 EN 60950 /2001 Following the provisions of 89/336/EEC and 73/23/EEC directives. Winfried Deckelmann Weiterstadt, August 2005 Place and date of issue Legal Signature USA FCC 47 Part 15 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to the part 15 of the FCC Rules. [. . . ] The module also provides 3 composite outputs in parallel to the selected component analog output. The module provides two re-clocked SDI loop through signals for further use downstream. The TE-D20 has a variety of features, which include: · · · · · · · · · Component RGB or YUV or S video outputs 3 x Composite (CVBS) output PAL or NTSC operation Internal color bars Internal 2x over sampling (27MHz) 2 x reclocked SDI loop through outputs Local DIP-switches and LED's for control and status monitoring. Remote control interface. Page 7 Reference Manual TE-D20 Version 2. 0 The module has a built in micro-controller with local controls, status and alarm indicators and well as internal flash ram for storing setups. Any operational parameters configured and stored into the module are recalled when powered up. Remote control and remote status monitoring is possible when used with the rack frame option and host controller. The TE-D20 is part of the 3000 series of MiniModules, which offer high quality, modularity and flexibility in a very small form factor ideal for applications where space is at a premium. The modules can be used either stand alone using the optional power supply brick, or as part of a tightly integrated space saving system where up to 10 MiniModules can be mounted utilizing the optional FERGUSON R FR 3005 / 3010 rack housing. This includes integrated power supply and optional remote control interfaces. Page 8 Reference Manual TE-D20 Version 2. 0 Functional Diagram Figure 1 below is the basic functional diagram for the TE-D20 MiniModule. SDI LOOP 1 DRV SDI LOOP 2 SDI IN EQ PLL SER PAR G or Y B / U / Y (S) R / V / C (S) Color Bars DAC CVBS CVBS CVBS Remote Micro Controller Switch Alarm Status Figure 1- TE-D20 Functional Diagram Module Layout Figure 2 shows the physical layout of the TE-D20 MiniModule. Video I/O is made through standard 75 Ohm BNC video connections. Module configuration is set via a small dip-switch located behind an access hole in the bottom of the module. Each module plugs into a connection bus, which provides common power for all modules. (no R PS external power supplies are needed). Remote control and status monitoring of all modules is possible with the addition of the R CT 5020 rack controller and R CT 5030 master controller options. Please refer to the respective reference manuals for these options for details of mechanical installation. Please see the section following the table for more detail on the switch function. Switch 1 2 3 4 5 6 7 8 Setting ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF Function Local control enabled (toogle for reaquire) Local control disabled RGB component output YUV component output Selection on switch 2 enabled S- Video output Active line length 720 pixels Active line length 702 pixels Test signal ON (Color Bars) Test signal OFF (Color Bars) Test signal = NTSC format Test signal = PAL format If no input, output = BLACK If no input, output = color bars Not used Page 16 Reference Manual TE-D20 Version 2. 0 Switch Function Detail All settings are stored in Flash Ram inside the module (see Auto Store section in this manual). It is recommended that switch 1 is set to OFF to disable further local control when the module is configured for use. Dip Switch 1 This switch enables local control using the dipswitches. ON enables local control and makes selections on the dip-switch active, and OFF disables local control (locking out any changes). If local control is disabled from remote (LED 3 OFF), please toggle Dip Switch 1 to reaquire local control Dip Switch 2 This switch selects either RGB or YUV component analog outputs from the module. Note: Composite video outputs are always present. Dip Switch 3 This is used to select the Y/C (S-Video) output from the module. [. . . ] External desk power supply module for 4 Series 3000 MiniModules. Mounting bracket for 4 MiniModules Rack Frame 1. This is a basic 19 inch rack mountable frame which can accommodate 10 MiniModules with power bricks R PS 1 or can be extended with the R FR 3010. This is a card cage with integrated central power supply, optional redundant power supply and optional controller, which can accommodate 10 MiniModules. [. . . ]