User manual FESTOOL _PSBC 400 EB

[. . . ] [1-1] Chip guard [1-2] On/Off switch [1-3] Variable speed trigger (only PSBC 400 EB) [1-4] Switch lock (only PSBC 400 EB) [1-5] Adjusting wheel for stroke speed control [1-6] Buttons for releasing the battery pack [1-7] Extractor connector [1-8] Saw table change lever [1-9] Saw blade ejection [1-10]Replaceable saw table [1-11]Pendulum stroke switch [1-12]Base runner The illustrations specified are located at the beginning and end of the operating manual. Jigsaws are designed for sawing wood and similar materials similar to wood. With the special saw blades offered by Festool, these machines can also be used for sawing plastic, steel, aluminium, non-ferrous metal and ceramic plates. Cutting depth (depending on saw blade) Wood Aluminium Steel Weight without battery pack Safety class 6 Ah, 100 % Permitted charging temperature range Temperature monitoring Battery pack Order number Voltage Capacity Weight BPS 12 Li 494831 10. [. . . ] we recommend Festool saw blade S 105/4 FSG. Inserting saw blade Always disconnect the battery pack from the machine before every tool change!X If necessary, push the chip guard [4-1] upwards. X Push the saw blade [4-4] into the opening as far as the stop with its teeth in cutting direction [4-2]. A loose saw blade can fall out and cause an injury. L In the case of very short saw blades, it is advisable to remove the saw table (see chapter 7. Ejecting saw blade L When ejecting the saw blade, hold the electric power tool such that no persons or animals can be injured. x Push the saw blade ejection [4-3] forwards as far as the stop. If the saw blade is not ejected: run jigsaw 3 - 10 seconds at a high speed. Actuate saw blade ejector mechanism [4-3] once again. 2 Using the chip guard The chip guard [4-1] prevents chips flying away and improves the efficiency of the chip extraction system. X Using minimal pressure, push the chip guard [4-1] downwards. 3 Inserting splinterguard The splinterguard makes cuts with splinter-free cutting edges possible, even on the exit side of the saw blade. X With the machine switched off, push the splinterguard [5-1] onto the guide up to the saw blade [5-2], X switch on the jigsaw, Risk of injury, electric shock X Always disconnect the battery pack before any type of work on the machine!With the machine running (Speed range 5), push the splinterguard in on a flat plane until it is flush with the front edge of the saw table. 3 mm further to the rear and continue using it. L To guarantee reliable operation of the splinterguard, it must seal tightly on both sides of the saw blade. For splinter-free cuts, therefore, a new splinterguard should also be used after every saw blade change. Instead of the saw table, the angle table WTPS 400 or adaptation table ADT-PS 400 can be installed at the support. Never saw without the saw table, or one of the other tables offered in the Festool accessories program. 6 Adjusting the pendulum stroke In order to process different materials with an optimum feed movement the pendulum jigsaws have an adjustable pendulum stroke. Select the desired setting with the pendulum stroke switch [1-11]: setting 0 = pendulum stroke off setting 3 = maximum pendulum stroke Recommended settings of the pendulum stroke Hard and soft wood, chip board, wood 1 - 3 fibre board Wood core plywood, plywood, plastics 1 - 2 Ceramic Aluminium, NF metals Steel 0 0-2 0-1 Always work with a dust extractor. [. . . ] X Once the battery pack has cooled, perform a functional check using the charger. Use only original Festool accessories and Festool consumable material intended for this machine because these components are designed specifically for the machine. X Insert the centring mandrel [11-2] in the bore [11-4] of the circle cutter, which is aligned with the saw blade. The equivalent amount of lithium in the LiIon battery pack is less than the applicable limit value and certified as per UN manual ST/SG/ AC. [. . . ]