User manual FESTOOL OF 1010 Q

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual FESTOOL OF 1010 Q. We hope that this FESTOOL OF 1010 Q user guide will be useful to you.

Lastmanuals help download the user guide FESTOOL OF 1010 Q.


Mode d'emploi FESTOOL OF 1010 Q
Download
Manual abstract: user guide FESTOOL OF 1010 Q

Detailed instructions for use are in the User's Guide.

[. . . ] Save all warnings and instructions for future reference. The term , , power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. 2 Tool-specific safety rules - Do not exceed the maximum speed specified on the tool and/or keep to the speed range. - The clamping collet should only be used to clamp tools with a shank diameter appropriate for the collet. [. . . ] The individual height of each sensing stop can be adjusted with a screwdriver: Sensing stop min. 4) down so that it shows 0 mm on the scale (1. B) Setting the milling depth The desired milling depth can be set either with the quick depth adjustment or with the fine depth adjustment. 7) up until the pointer shows the desired milling depth. Clamp the stop cylinder in this position with the clamping lever (1. Turn the adjusting wheel to the next mark on the scale to adjust the milling depth by 0. With edge routing, the best extraction effect is obtained with the extractor hood AH-OF, available as an accessory. kSF-OF chip catcher Using the KSF-OF chip catcher (9. 1) (sometimes included in the scope of delivery), the efficiency of the extraction can be increased when routing edges. installation is similar to that of the copying ring. The hood can be cut off along the grooves (9. 2) using a hacksaw and can thus be reduced in size. The chip catcher can then be used for interior radiuses up to a minimum radius of 40 mm. Working with the machine Always secure the workpiece in such a manner that it cannot move while being sawed. The machine must always be held with both hands by the designated handles (1. When routing (ensure feed direction of power tool is the same as cutting direction of tool, Fig. Aluminium processing When processing aluminium, the following measures must be taken for safety reasons: - Pre-connect a residual current circuit-breaker (FI, PRCD). 2 Freehand routing Freehand routing is the method normally used for lettering or shapes, and for routing edges using cutters with a guide pin or ring. 2) supplied can be used for routing parallel to the edge of the workpiece (not supplied with , , Module 5A): - Secure both guide rods (3. 10) on the router base to the required distance and secure them by turning the rotary knob (3. This distance can be adjusted faster and more precisely with the fine precision adjustment (3. 3) of the parallel guide, - set the desired distance with the adjusting screw and retighten the rotating knobs. [. . . ] All maintenance and repair work which requires the motor casing to be opened may only be carried out by an authorised service centre. always keep the machine and the ventilation slots clean. The tool is fitted with special motor brushes with an automatic cut-out. When the brushes become worn the power supply is shut off automatically and the tool comes to a standstill. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE FESTOOL OF 1010 Q

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual FESTOOL OF 1010 Q will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag