User manual FIRENZI FRF120

[. . . ] REFRIGERATOR FRF 120 INSTRUCTION BOOKLET 2222685-21 Important Safety Instructions These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using this appliance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. Prior to Installation ¥ Check the appliance for transport damage. Under no circumstance should a damaged appliance be installed. [. . . ] Do not use a mechanical device or any artificial means to speed up the thawing process other than those recommended by the manufacturer. However, when the ice becomes very thick on the inner liner, complete defrosting should be carried out as follows: 1. pull out the plug from the wall socket or turn the thermostat knob to the ÇOÈ setting; 2. remove any stored food, wrap it in several layers of newspaper and put it in a cool place; 3. leave the door open, place a basin on the top shelf of the refrigerator compartment, under the drain hole, remove the plug as shown in the figure; P F S. I. 011 PR151 4. when defrosting is completed, dry the interior thoroughly and refit the plug. Keep the scraper for future use; turn the thermostat knob back to the required setting or replace the plug in the power socket. After two or three hours, reload the previously removed food into the compartment. Important A temperature rise of the frozen food packs, during defrosting, may shorten their safe storage life. 7 Maintenance and Cleaning Warning Before any maintenance or cleaning work is carried out, DISCONNECT the appliance from the ELECTRICITY supply. Important This appliance contains hydrocarbons in its cooling unit maintenance and recharging must therefore only be carried out by authorised technicians. Changing the light bulb Should the interior light fail to work, first switch off the appliance and disconnect from the electricity supply, then replace the bulb as follows: 1. Unscrew the light cover and then pull it outward by pressing as shown in the figure. Unscrew the bulb and replace it with a new 15 watt bulb (available from your nearest Service Force centre). Replace the light cover by sliding it into its original position and replacing the screw. Internal cleaning Clean the inside and accessories with warm water and bicarbonate of soda (5ml to 0. 5 litre of water). NEVER USE DETERGENTS, ABRASIVE POWDERS, HIGHLY PERFUMED CLEANING PRODUCTS OR WAX POLISHES, TO CLEAN THE INTERIOR AS THESE WILL DAMAGE THE SURFACE AND LEAVE A STRONG SMELL. Clean the drain hole of the water trough at regular intervals and make sure that the drain hole is never obstructed, so that the defrost water may flow freely. Important Do not use abrasive products. D411 When the appliance is not in use When the appliance is not in use for long periods, disconnect from the electricity supply, empty all foods and clean the appliance, leaving the door ajar to prevent unpleasant smells. Periodic cleaning The appliance is equipped with a ventilation grid. Keep clean to guarantee good ventilation and good working order of the appliance. An accumulation of dust will affect the performance of the appliance and cause excessive electricity consumption. The structure of the appliance permits cleaning of the rear zone close to the wall, using a vacuum cleaner. Remove the plinth (1), then the ventilation grid (2); 2. Carefully pull the air deflector out (3), checking that there is no water left from the defrosting. 3 2 1 S. I. 013 8 Something not Working? Before contacting your local Service Force Centre check the following points. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. Symptom No power to appliance Solution - Check there is power at the socket. [. . . ] - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent amendments. Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of breakdown. BLUE D207 CORD CLAMP 13 AMP BROWN 13 Door reversal To reverse the opening direction of the door, proceed as shown in the figures: 6 4 1 7 8 5 2 3 1 2 Attention After completion of the door reversing operation, check that the door gasket adheres to the cabinet. If the ambient temperature is cold (i. e. in Winter), the gasket may not fit perfectly to the cabinet. [. . . ]