User manual FLAM DESIGN 63-64 DIMENSIONS

[. . . ] Mention of software products manufactured by other companies does not necessarily constitute endorsement by the manufacturer. While all reasonable efforts have been made to make this document as accurate and helpful as possible, we make no warranty of any kind, expressed or implied, as to the accuracy or completeness of the information contained herein. The most up-to-date drivers and manuals are available from the web site: http://www. okiprintingsolutions. com Trademark Information Oki and Oki Data are registered trademarks of Oki Electric Industry Company Ltd. Apple, Macintosh and Mac OS are registered trademarks of Apple Computers Inc. [. . . ] Usually, such A4 paper print width is set slightly narrower than 8 inches (about 7. 93 inches). This setting cannot print 80 10cpi characters (only prints up to 78 10-cpi characters). 80 characters set at A4 Print Width widen the right and left margins. A PCL command selects or selects/deselects Auto CR/LF mode. 44 ­ MPS610c/MPS711c User's Guide ITEM PCL Setup (cont. ) White Page Skip SETTINGS On/Off EXPLANATION Sets whether to eject a page without any data to print (blank page) upon reception of FF command (OCH) in PCL Mode. Sets action when CR code is received in PCL. CR: Carriage Return CR+LF: Carriage Return and Line Feed CR Function CR/CR+LF LF Function LF/LF+CR Sets action when LF code is received in PCL. LF: Line Feed LF+CR: Line Feed and Carriage Return Print Margin Normal 1/5 inch 1/6 inch Sets a non-printable area of paper. The width of the area along the right and left sides of paper (left and right sides depend on paper orientation). NORMAL: PCL emulation compatible, approximately 1/ 4~1/4. 3INCH (depending on paper) is outside the printable area. True Black On/Off Sets whether to use Composite Black (CMYK mixed) or Pure Black (K only) for the black (100%) in image data. OFF: Mode using Composite Black ON: Mode using Pure Black (PCL only) 45 ­ MPS610c/MPS711c User's Guide ITEM PCL Setup (cont. ) Pen Width Adjust SETTINGS On/Off EXPLANATION When minimum width is specified in PCL, sometimes a 1dot line, looks broken. With PEN WIDTH Adjust set to ON, when the minimum width is specified, the line width will be emphasized so as to look wider than a 1-dot line. Selects limitation to the toner layer thickness. If paper curl occurs in dark printing, selecting MEDIUM or LIGHT sometimes helps reduce this curl. Enable/Disable 100% output against the CMY100% TRC compensation. Ordinarily, the TRC compensation function holds control for the appropriate print density; thus 100% output is not always possible. Selecting ENABLE will enable 100% output in any individual color. The actual print, including the TRC compensation function is limited to an appropriate area. This function is for special purposes such as specification in CMYK color reduction in PS. CMY 100% Density Enable/Disable CMYK Conversion On/Off Setting to "OFF" will simplify the conversion process of CMYK data, which will reduce the processing time. This setting is ignored when Ink Simulation function is used. PS only 49 ­ MPS610c/MPS711c User's Guide ITEM Memory Setup Receive Buffer Size SETTINGS Auto 0. 5 megabyte 1 megabyte 2 megabyte 4 megabyte 8 megabyte 16 megabyte 32 megabyte Resource Save Auto Off 0. 5 megabyte 1 megabyte 2 megabyte 4 megabyte 8 megabyte 16 megabyte 32 megabyte EXPLANATION Sets the size of receive buffer Sets the size of resource saving area. Flash Memory Setup Initialize Execute Initializes Resident FLASH. When the Enter button is pressed, the following confirmation message appears. Yes/No If No is selected, the previous menu display resumes. [. . . ] · Direct Network Printing Utility (LPR) For printing on an Ethernet network without the need for a print server. · Network Extension For use when your printer is connected over a TCP/IP network. Check the printer status and configuration from the Printer )Properties tab in the printer driver. · Color Swatch Utility Print a color swatch and use the indicated RGB values to set up the color(s) of your choice in your graphics/design software application. [. . . ]