User manual FLAM GMT 80-56 DIMENSIONS

[. . . ] Printer software diskette (to install printer software without CDROM) 4. Black plastic light-shield bag (to store image drum if you need to ship the printer) 6. Warranty Registration Card If you are missing anything, contact your dealer. Selecting a Location for Your Printer · · · · · · · A firm surface such as a table or desktop Space to open the cover and pull out the paper tray and the rear output extender Air circulation around the printer to prevent overheating (minimum of 4 inches) A nearby power source Room temperature of 50° to 90°F (10° to 32°C). Relative Humidity of 20- 80% No direct sunlight Visit the FLAMDATA Web Site http://www. okidata. com for the latest information on: · Product Guides · Customer Support · Software Drivers · Corporate Information · Documentation Image drum cartridge ¯2 FLAMPAGE 10ex User's Guide 1 Remove the Image Drum Protective Paper 1. [. . . ] Labels should cover the entire carrier sheet­carrier and adhesive must not be exposed to any part of the printer. Use rear paper output ­ to reduce heat exposure and curling. · · · · · ¯32 FLAMPAGE 10ex User's Guide Section 3 ² Printer Maintenance This Section provides the following printer maintenance information: · · · · Replacing the Toner Cartridge Replacing the Image Drum Cleaning the LED Array Printing a Cleaning Page 4. To install a new toner cartridge, follow the instruction in Section 1 (or the instructions included in the toner cartridge kit). Be sure to clean the LED array. ¶ Drum and Toner are consumables and as such are subject to a 90-day warranty on workmanship. Replacing The Toner Cartridge Replace the toner cartridge after TONER LOW displays on the printer's front operator panel, or on your screen in the Status Monitor if you have installed the printer software. After TONER LOW displays, the printer will print 100 more sheets, then display TONER EMPTY and stop printing. Printing will resume when a new toner cartridge is installed. You will need a new toner cartridge (FLAMPAGE 10 and 12 Series Type 5 Toner Kit, Part# 52109001). Grasp the lock lever and pull towards the front of the printer to unlock the cartridge. Lift out carefully and discard the used toner cartridge. Toner Cartridge Life How long your toner cartridge lasts depends on the print density, the percentage of the page that prints black. · · · A typical letter has 3% to 5% print density, graphics usually have higher density. Higher print density means toner is used up faster. At 5% print density, a toner cartridge will print an average of 2, 000 pages. Click the Operator Panel button on the status monitor Controls tab. 2. The cleaning page prints, then OFF-LINE displays. Press ON-LINE to enter online mode. 3. Follow the on-screen instructions. FLAMPAGE 10ex User's Guide 35 ° Section 4 ² Problem Solving 2. Remove the sheet that did not feed. Clearing Paper Jams To reduce paper jams: · Do not fill tray above Paper Full mark. · Use only recommended paper weight - Tray: 16 to 28 lb. (60 to 105 g/m2) - Manual feed: 16 to 32 lb (60 to 120. 5 g/m2) · Do not open the cover, or remove the paper tray during a print job. · Do not switch paper exit paths while printing. · Use paper that is smooth and of high quality. · Store paper in its ream wrapper until you are ready to use it, and keep it away from moisture or other conditions that can cause it to wrinkle or curl. · Avoid printing on both sides of the paper for more than a few pages, or preprinted documents that have been in a photocopier. [. . . ] Amorphous Fumed Silica (less than 1% by weight) CAS# 67762-90-7 OSHA PEL 15. 0 mg/m3 for total dust ACGIH TLV 10. 0 mg/m3 for total dust Note This product is not regulated under Section 313 of SARA, Title III. Physical Data Melting Point: 110°C (230°F) Boiling Point: Not applicable Vapor Pressure: Not applicable Vapor Density (Air=1): Not applicable Evaporation Rate (Butyl Acetate=1): Not applicable Specific Gravity (H2O=1): 1. 15 Solubility in water: Negligible Appearance and odor: Black granules, no odor Fire and Explosion Hazard Data Flash Point (Method Used): Not applicable Flammable Limits Lower Explosive Limit: Not applicable Upper Explosive Limit: Not applicable Extinguishing Media: Water, CO2, Dry Chemical, or Foam Special Fire Fighting Procedures: Do not use methods that may create a dust cloud, such as high pressure water and/or steam Unusual Fire and Explosion Hazards: Organic components decompose at 200-455°C (392-851°F). Material may explosively combust when finely suspended in air. Thermal decomposition of organic components may result in release of oxides of carbon and nitrogen. Toner inhaled Toner gets in the eyes Note Hazardous Ingredients Styrene-Butyl Acrylate Copolymer (91% by weight) CAS# 25767-47-9 OSHA TWA 15 mg/m3 for total dust ACGIH TLV 10 mg/m3 for total dust Carbon Black (5-7% by weight) CAS# 1333-86-4 OSHA TWA 3. 5 mg/m3 ACGIH TLV 3. 5 mg/m3 Paraffin Wax (less than 3% by weight) CAS# 8002-74-2 OSHA TWA 2 mg/m3 for total dust ACGIH TLV 2 mg/m3 for total dust ° FLAMPAGE 10ex User's Guide 53 Health Hazard Data Routes of Entry: Inhalation, Ingestion, Eyes, Skin. Styrene-Butyl Acrylate Copolymer Subcutaneous implantation of polymeric styrene powder in rats has induced tumors at the site of implantation. [. . . ]