User manual FLAM LINEA 186-57 DIMENSIONS

[. . . ] Copyright Information Copyright 2001 by Oki Data. Written and produced by the Oki Data Training and Publications Department. Contact Information Please address any comments on this publication to: Web Site Please visit Oki Data's multilingual web site at: http:// www. okidata. com Mailing Address Oki Data Americas, Inc. Laurel, NJ 08054-4620 Trademark Information FLAM and MICROLINE are registered trademarks of Oki Electric Industry Company, Ltd. [. . . ] Shake the cartridge to distribute the toner. Only the FLAMPAGE Type 5 Toner Cartridge will fit in this unit (Part# 52109001) ! 14e Setup Guide | E-9 5 Lower the right side into the toner well, aligning the lock lever slot with the ridge in the drum cartridge. 6 When the cartridge is in place, push the lock lever forward until it stops. PU SH 7 Lower the printer cover and press firmly to close. E-10 | FLAMPAGE 14e Loading Paper 1 Slide the tray out of the printer. 3 Fan a stack of paper and place it in the tray under the tabs. Do not fill above the "PAPER FULL" mark. paper. ! ! The paper gauge (1) indicates how much paper remains in the tray; you don't have to slide the tray out to check. 2 Adjust the tray guides for the correct paper size. ! Recommended paper weight for the tray is 16 to 28 lb (60 to 105 g/m2). 4 Place the tray into the printer then push closed until the tray locks in place. Using Legal Size Paper To load legal size paper, open out the tray extender and adjust the rear paper guide. 14e Setup Guide | E-11 Paper Exit Paths Two paper exit options are available. Select the paper path that is appropriate for the media you are using. Rear Paper Exit The rear paper exit tray provides a straighter paper path. Use rear exit when printing on heavy paper, envelopes, labels, and transparencies. · Printed pages exit face up in reverse order · Maximum output is 50 sheets of 20-lb. paper · Use rear exit for printing on heavy paper, envelopes, labels, transparencies or odd size paper Top Paper Exit Use the top paper exit for most printing jobs. · Printed pages exit face down · Pages are stacked in the order printed · Exit bin holds 150 sheets of 20-lb. See Service and Support in the User's Guide for purchasing information. Turning on the Printer 1 Make sure the printer is off. ! POWER ON OFF F Connecting the Cable Make sure the printer and computer are off. 1 Insert the printer end of the cable firmly into the proper connector on the back of the printer. Fasten the cable to the printer securely. 2 Plug the cord into the printer first, then into a grounded outlet. 2 Connect the other end of the cable to the proper connector on your computer. Fasten the cable securely to your computer. 3 Turn the printer on. It takes about 10 seconds for the printer to initialize and warm up, and for the Ready light on the operator panel to turn on, indicating the printer is ready to receive data. 14e Setup Guide | E-15 Printer Drivers Printer Software Overview The CD-ROM provided with your printer includes printer drivers and the on-screen printer status monitor and operator panel required to use all the FLAMPAGE 14e features. Follow the steps in this guide to install the appropriate printer software on your computer system. Printer drivers must be installed so your software application can communicate with your printer and support all of its features. The FLAMPAGE 14e CD-ROM includes printer drivers for printing in the following environments: · Windows Me · Windows 2000 · Windows 98 · Windows NT 4. 0 · Windows 95 E-16 | FLAMPAGE 14e Status Monitor The status monitor program allows you to monitor and configure an FLAMPAGE 14e. In addition to displaying printer status messages, the status monitor provides remote access to the printer's operator panel. See page 22 for information on using the Status Monitor. Installing Printer Software Determine your computer's interface connection and operating system. Then proceed to the page listed for instructions to install the appropriate printer software. Parallel Connection Windows Me, 2000, 98, 95, NT 4. 0 see page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 USB Connection Windows 98, Me see page . . . . . . . . . . . . . . . . . . . . . . . . 19 Windows 2000, see page . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 7 Set print output quality, darkness setting. 8 Set power save delay time, toner save. 9 Print demo page, font page, menu settings, cleaning page. 14e Setup Guide | E-23 Using Power Save to Minimize Warm-up Time To minimize the printer's warm-up time between print jobs, adjust the Power Save feature in the Printer Menu Setup: 1 From the Windows Taskbar, open the Windows Programs list. 2 Choose FLAMPAGE 14e and click FLAMPAGE 14e Status Monitor. [. . . ]