User manual FLAM PIKKU DIMENSIONS

[. . . ] Mention of software products manufactured by other companies does not necessarily constitute endorsement by the manufacturer . While all reasonable efforts have been made to make this document as accurate and helpful as possible, we make no warranty of any kind, expressed or implied, as to the accuracy or completeness of the information contained herein. The most up-to-date drivers and manuals are available from the web site: http://www. okiprintingsolutions. com Trademark Information _______________________________ Oki and Oki Printing Solutions are registered trademarks of Oki Electric Industry Company Ltd. Adobe and PostScript are registered trademarks of Adobe Systems. [. . . ] Recommended replacement: after approximately 120, 000 sheets. User's Guide> 49 CONSUMABLE ITEM ORDER INFORMATION ITEM Toner, Black Toner, Cyan Toner, Magenta Toner, Yellow Image drum, Black Image drum, Cyan Image drum, Magenta Image drum, Yellow LIFE 18, 500 Letter pages @ 5% 16, 500 Letter pages @ 5% 16, 500 Letter pages @ 5% 16, 500 Letter pages @ 5% 42, 000 Letter pages avg 42, 000 Letter pages avg 42, 000 Letter pages avg 42, 000 Letter pages avg ORDER NUMBER 52124004 52124003 52124002 52124001 56124004 56124003 56124002 56124001 MAINTENANCE ITEM ORDER DETAILS ITEM Fuser unit LIFE 100, 000 Letter pages ORDER NUMBER 120V:42931701 230V: 42931702 Belt unit Waste toner bottle 100, 000 Letter pages 30, 000 Letter pages avg 42931601 42869401 User's Guide> 50 REPLACING CONSUMABLES/MAINTENANCE ITEMS Each consumable or maintenance item comes complete with its own installation details which give full instructions on replacement. You are advised to follow these instructions carefully. CAUTION! Only use genuine Oki Original consumables to ensure the best quality and performance from your hardware. Non-Oki Original products may damage your printer's performance and invalidate your warranty. Specifications subject to change without notice. All trademarks acknowledged. CLEANING THE LED HEADS You are advised to clean the LED heads: > any time you replace a toner cartridge (a LED lens cleaner is enclosed with each replacement toner cartridge) > if printing is showing signs of faded images, white stripes or blurred letters You can use a LED lens cleaner or dry, soft cloth for cleaning the LED heads. Open the top cover. User's Guide> 51 2. With an LED lens cleaner or soft cloth, gently wipe each of the four heads (1). Move the cleaner as shown, using a clean section of the cleaner with each pass. Be careful not to damage the guards (2). 1 2 3. Close the top cover. User's Guide> 52 CLEANING THE PAPER FEED ROLLERS Clean the paper feed rollers if paper jams frequently occur. Remove items like a wrist watch or bracelet and follow the correct steps to turn the printer off depending on whether a hard disk drive is installed. 2. Open Tray 1 side cover and pull out the paper guide plate (1). 1 User's Guide> 53 3. Remove Tray 1 completely from the printer. 4. Gaining access through the gap left by Tray 1, wipe the 3 paper feed rollers (2) with a soft cloth lightly moistened with water. 2 5. Replace Tray 1. User's Guide> 54 6. Return the paper guide plate to its original position and close Tray 1 side cover. 7. Turn on the printer. User's Guide> 55 CLEANING THE PRINTER CASING 1. Follow the correct steps to turn the printer off depending on whether a hard disk drive is installed. 2. Wipe the printer surface with a soft cloth moistened sparingly with water or neutral detergent. 3. Use a soft dry cloth to dry the printer surface. User's Guide> 56 4. Turn on the printer. User's Guide> 57 OPTIONAL ACCESSORIES This section describes optional accessory equipment for your printer. Your printer feed rollers are wearing out. The media weight or type have been wrongly set. SUGGESTED REMEDY Place the printer on a steady, level surface. Use media that has been stored in appropriate temperature and humidity conditions. Remove the sheets, jog them into alignment and reload them. Adjust the paper stop and paper guides of the tray, or the manual feed guide on the MP Tray to align the media properly. Wipe the roller with a cloth moistened with water. Select the correct printer menu settings for [Media Weight] and [Media Type]. User's Guide> 75 DEALING WITH UNSATISFACTORY PRINTING SYMPTOMS Vertical white lines can be seen on the printed page. POSSIBLE CAUSES The LED head is dirty. STEPS TO TAKE Wipe the LED head with a LED lens cleaner or with a soft cloth. Wipe the film with a LED lens cleaner or with a soft cloth. Wipe the LED head with a LED lens cleaner or with a soft cloth. Use paper stored in proper temperature and humidity conditions. Set a proper value for [Media Weight] and [Media Type] in the menu setup, or set one value thicker for [Media Weight]. [. . . ] Decrement setting when a white horizontal dotted line or a snowy image occurs in highcoverage print portions. Increment setting when a faded image occurs. Used for fine black adjustment for a significantly white horizontal dotted line, a significantly faded image or other such a problem that occurs in results printed on transparencies. Decrement setting when a white horizontal dotted line or a snowy image occurs in highcoverage print portions. [. . . ]