Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual FLUKE MPG2-H WITH PG7302. We hope that this FLUKE MPG2-H WITH PG7302 user guide will be useful to you.
Lastmanuals help download the user guide FLUKE MPG2-H WITH PG7302.
Manual abstract: user guide FLUKE MPG2-H WITH PG7302INSTALLATION
Detailed instructions for use are in the User's Guide.
[. . . ] x 1/8 in. (127 mm x 3 mm), DH500, flexible Elbow DH500 Tee DH500 Union DH500 Plug DH500/DH700 Adaptor, DH500F x 1/8 in. (3 mm) NPTM
500 MPa (72, 500 psi) 500 MPa (72, 500 psi) 500 MPa (72, 500 psi) 200 MPa (30, 000 psi) 400 MPa (60, 000 psi) 400 MPa (60, 000 psi) 400 MPa (60, 000 psi) 700 MPa (100, 000 psi) 200 MPa (30, 000 psi)
1 1 1 2
3068887 3068893 3068902 3126068
Note
Orientate weep holes on union, tee, and elbow facing up to facilitate leak check and purge. Install nipples into three way tee and elbow: Install the 2. 75 in. [. . . ] nipple should be inserted into the test port of the RPM4 or PG7302. Do not tighten the gland in the RPM4 or PG7302 yet, since it will be tightened when the system is primed. Install a DH500M to 1/8" NPT male adaptor in the DUT if necessary: The 1/8 in. NPT male adaptor can be used to connect the remaining flexible 5 in. nipple to DUTs with 1/8 in NPT female ports. If you intend to use the adaptor,
1 1 1 1 2
3068361 3068501 3068520 3068470 3068785
Introduction
This kit provides the tubing and fittings necessary to connect an MPG2-H pressure controller to either an RPM4 reference pressure monitor or to a PG7302 piston gauge, and also to a device under test. This document contains instructions for connecting the fittings and tubing.
Installation of Interconnections
Remove Plugs from MPG2-H, Tee, Union and RPM4 or PG7302: Unscrew the glands from the test ports of the MPG2-H and RPM4 or PG7302. Remove the collar and plug from inside each gland. There should be one stainless steel plug. Install glands and collars onto flexible 5 in. nipple: Slide a gland over a nipple so that the threads of the gland face outward. Next, screw a collar onto the nipple by turning it to the LEFT. Allow two nipple threads to show between the collar and nipple tip. Use collars and glands from tee, elbow and union.
wrap Teflon® thread tape around the NPT threads three times and install it into the DUT. The DUT will be connected to the test line with the remaining flexible 5 in. This nipple can be installed either in the 3-way tee, or in the port on top of the MPG2-H. The tube can be slightly bent if necessary. Install the nipple in the desired location. [. . . ] Do not generate pressure greater than the maximum operating pressure. · High pressure fluids are potentially hazardous. Energy stored in pressurized fluids can be released unexpectedly and with extreme force. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE FLUKE MPG2-H WITH PG7302
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual FLUKE MPG2-H WITH PG7302 will begin.
