User manual FLY 00779

[. . . ] If this doesn't suit you, it's very easy to change it ­ when you've read this introductory section, simply go to the section that contains your programmer model. THE LP112 24hr ELECTRONIC PROGRAMMER Cont. . . button and you'll see `SET PROG?'. Current Models DUAL CHANNEL Programmer for heating AND hot water Drayton Lifestyle Switchmaster Tempus 1, 2 (new models) LP111, LP711 300 N N N L L L 1 1 4 3 3 1 2 2 4 4 DUAL CHANNEL PROG? Discontinued/Competitors' Models ACL Drayton Switchmaster Danfoss Randall Danfoss Randall Danfoss Randall Danfoss Randall Danfoss Randall Danfoss Randall Danfoss Randall Grasslin Towerchron Grasslin Towerchron Honeywell Honeywell Horstmann Horstmann Horstmann Horstmann Landis & Staefa Landis & Staefa Landis & Staefa Potterton Myson Sangamo Smiths Smiths Smiths Sunvic Sunvic Venner TC (Towerchron) Tempus 1, 2 (old models) 980 TS15, 75 (Mk18) TS715 TS975 SET1, SET1E SET4 103, 103E, 103E5, 103E7 911, 971 QE1 T2001, T2001Q ST 6100A, ST 6100C ST 7000B Centaur SC1, SC7 Centaur Plus, C11, C17 Emerald 423, Pearl Auto 517, Coronet, H11, H17 RWB3 RWB30, RWB50, 100, 152, 170 RWB7 EP4000, 4001, 4002, 5002 M6 Centroller Mk1, Mk2 Centroller 30 Centroller 300, 980 Select 107 SP20, SP35 Vennerette 2 N N N N N N N 5 N N N N N N N N N N L N 4 N 1 N N N N 1 L L L L L L L 6 L L L L L L L L L L L 2 L 6 L 2 L L L L 4 1 4 1 1 5 5 5 3 5 2 1 4 2 3 5 2 4 5 3 3 4 1 3 LINE 7 2 1 4 4 4 4 4 1 6 4 7 4 3 3 4 4 4 4 4 3 4 1 2 4/5 1 3 5 LOAD 3 4 Programmer for heating AND hot water At the side of the display there are four operating modes: OFF TIMED ONCE ON = continuously off. = on for 1 period a day, from the start of ON1 to the end of OFF3. Set all weekdays First you set the times that are going to be the same for each weekday, then you can select each day individually and make any further adjustments. [. . . ] PROGRAMMER ONLY The programmer must be set to the type of system it is to control. The link on the back of the unit has two settings ­ P and G. P = a fully pumped and controlled system ­ allowing heating and hot water to be set separately. Notice that on the standard program ON2 and OFF2 are set to the same time. * This means your system won't respond, but if you want to activate that middle period, or change any other timings ­ read on. I Press the YES button, and the display will ask `SET CH PROG?'. CH PROG? I Press YES and you'll see ON1, the start of your first central heating period. Adjust it in 1-minute steps using the ­ and + buttons. If the ­ and + buttons are held down, the time changes in 10-minute steps. The standard program Your system will come on for up to 3 heating periods every 24hrs. ON1 starts the first one, OFF1 finishes it, and so on. Notice that ON2 and OFF2 are set to the same time. * This means your system won't respond, but if you want to activate that middle period or change any other timings ­ read on. USING AN EXISTING WALL-PLATE Loosen the securing screws on the old programmer and unplug it. Check that there's 70mm clearance to the right of the wall-plate, and 25mm above it. Check the chart on the next page to compare terminals and if necessary, change the wiring of the wall-plate to suit. Now plug the Lifestyle unit into the wall-plate and tighten the securing screws. But it's easy to make changes, and have heating and water working independently ­ just follow the instructions. If you need to reset your timings to the standard program and start again, press `SET' and `+' together to go back to the pre-set program. If you don't press anything for two minutes, the programmer automatically goes back to normal operation. The standard program Your system will come on for up to 3 heating periods every 24hrs. ON1 starts the first period, OFF1 finishes it, and so on. Notice that ON2 and OFF2 are set to the same time. * This means your system won't respond, but if you want to activate that middle period, or change any other timings ­ read on. SWITCHING ON 1 ­ start of first timed period OFF 1 ­ end of first timed period ON 2 ­ start of second timed period* OFF 2 ­ end of second timed period* ON 3 ­ start of third timed period OFF 3 ­ final switch-off of the day WEEKDAYS HW 6. 30am 8. 30am 12. 00pm 12. 00pm 4. 30pm 10. 30pm CH 6. 30am 8. 30am WEEKENDS HW 7. 00am 9. 00am CH 7. 00am 9. 00am 12. 00pm 12. 00pm 4. 00pm 11. 00pm THE LP722 7-DAY ELECTRONIC PROGRAMMER LP722 ­ a 7-day program allowing for different timings on each day of the week, with central heating and hot water working independently for up to 3 heating periods each day. If the timings haven't been set for you, then your programmer will still be on the factory-set standard program. This has central heating and hot water operating together ­ with the option of having different timings for each day of the week. But it's easy to make changes, and have heating and water working independently ­ just follow the instructions. If you need to reset your timings to the standard program and start again, press `SET' and `+' together to go back to the pre-set program. If you don't press anything for two minutes, the programmer automatically goes back to normal operation. [. . . ] Adjust it in 1-minute steps using the ­ and + buttons. If the ­ and + buttons are held down, the time changes in 10-minute steps. PROGRAMMER NL1234 CYLINDER THERMOSTAT * SCH 2C1 # SET TO 'P' HTS 3 3124 5 #- LINK L-1 FOR 230V OUTPUT 21 64 8 6 Set the hour I Press SET?, and you'll see OFF1, the end of your first central heating period. Adjust this in the same way, press SET?, then repeat the procedure for ON2, OFF2, ON3 and OFF3. I Press YES once, and then the hour will start to flash. [. . . ]