User manual FLYMO L470

[. . . ] L470 GB D F NL IMPORTANT INFORMATION Read before use and retain for future reference WICHTIGE INFORMATION Bitte vor dem Benutzen des Gerätes durchlesen und gut aufbewahren RENSEIGNEMENTS IMPORTANTS A lire avant usage et à conserver pour référence ultérieure BELANGRIJKE INFORMATIE Leest u deze informatie voor het gebruik en bewaar ze voor toekomstige raadpleging VIKTIG INFORMASJON Les bruksanvisningen før bruk og oppbevar denne for senere bruk. TÄRKEÄÄ TIETOA Lue tämä ennen käyttöä ja säilytä myöhempää tarvetta varten S DK E P VIKTIG INFORMATION Läs anvisningarna före användningen och spara dem för framtida behov VIGTIGE OPLYSNINGER De bør læse dette før brug og gemme til senere henvisning INFORMACIÓN IMPORTANTE Léase antes de utilizar y consérvela como referencia en el futuro INFORMAÇÕES IMPORTANTES Leia antes de utilizar e guarde para consulta futura INFORMAZIONI IMPORTANTI Leggere prima dell'uso e conservare per consultazione futura N SF I A 1 90 2 5 3 4 0 B 2 1 C 3 D 1 1 2 2 3 E F H G J 1 K L M 9 N 8 7 5 6 4 3 2 1 P Q 6 5 1 3 7 4 2 GB - CONTENTS 1. Operator Presence Control (OPC of Veiligheids hendel) 2. BedienerpräsenzKontrollvorrichtung 2. [. . . ] Put the handle in the Parking position (D2). When the engine has stopped, lower the lawnmower to the ground. Close the fuel tap (J1) and the fuel tank air vent screw. Adjusting the cutting height Adjusting the Cutting Height · Never use more than 2 cutting height spacers. · Spacers can only be fitted between the blade and the fan and never between blade and the bolt (M). Ensure the Operator Presence Control is released, when the engine has stopped rotating disconnect the spark plug lead. Close the fuel tank air vent screw and fully close the fuel tap (J1). Remove the blade bolt (M1) and blade (M2) as described in Removing the Blade and Fan below. For a Lower Cut - Add spacers (M3) to a maximum of 2. For a Higher Cut - Take spacers (M3) away. Refit the blade as described in Fitting the Blade and fan below. Place the handle in the mowing position (D3). Start from the edge, mow in a clockwise direction (N). Your lawn will suffer if more than one third of its length is cut at one time. Removing & Fitting the Blade & Fan WARNING · Always handle the blade with care - sharp edges could cause injury. · Spark plug lead may be hot - handle with care. Removing the Blade and Fan · Renew your metal blade after 50 hours mowing or 2 years whichever is the sooner regardless of condition. · If the blade is cracked or damaged replace it with a new one. Ensure the Operator Presence Control is released, when the engine has stopped and the blade has stopped rotating - disconnect the spark plug lead. Close the fuel tank air vent screw and fully close the fuel tap (J1). To remove the blade bolt (M1), hold the fan (M4) firmly and with the spanner provided loosen the blade bolt by turning it anti-clockwise. Remove the blade bolt (M1), blade (M2), spacers (M3) and fan (M4). Inspect for damage and clean as necessary. Fitting the Blade and the Fan · Before using always visually inspect to see that blades and bolts are not worn or damaged. [. . . ] * Failures as a result of not using the product in accordance with the instructions and recommendations contained in this Operator's Manual. * Machines used for hire are not covered by this guarantee. * The following items listed are considered as wearing parts and their life is dependent on regular maintenance and are, therefore not normally subject to a valid warranty claim: Blades, belts, cables, recoil ropes, filters. Electrolux Outdoor Products does not accept liability under the warranty for defects caused in whole or part, directly or indirectly by the fitting of replacement parts or additional parts that are not either manufactured or approved by Electrolux Outdoor Products, or by the machine having been modified in any way. Environmental Information Electrolux Outdoor Products are manufactured under an Environmental Management System (ISO 14001) using, where practical, components manufactured in the most environmentally responsible manner, according to company procedures, and with the potential for recycling at the end of the products' life. [. . . ]