User manual FLYMO R32

[. . . ] RE320 RE32 R32 FO T IN TA N ce P O R ore use feren I M bef re re ad futu Re for tain & re IO M AT R N For all customer enquiries or for replacement parts, contact:- 01325 300303 www. flymo. com eop. customer. services@electrolux. co. uk ¤ 1 Carton Contents start/stop lever cable clip nut (if applicable) lock off button upper handle plastic handle knob grassbox upper grassbox lower electric cable with moulded on plug spanner/scraper tool deck instruction manual switchbox washer bolt lower handles safety flap lower handle fixing screws motor cover wheel assembly IMPORTANT !Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:Electrolux Outdoor Products Customer Service Department direct Telephone : 01325 300303 Fax : 01325 318193 Safety If not used properly this lawnmower can be dangerous!This lawnmower can cause serious injury to the operator and others, the warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this lawnmower. [. . . ] Locate 2 screws into the holes in the handles. Using a pozidrive screwdriver, secure the screws into the lower handles, ensuring the point of the screw stays inside the handle. Insert lower handles with screws attached, into the deck and fully tighten screws. (B) NOTE: The screw will form its own thread. Assembly of Upper Handles to Lower Handles. Ensure the upper handle is located correctly with the lock-off button on the switchbox uppermost. Ensure the upper handle and the lower handle are aligned correctly. (C) 3. Fit the bolts, washers and handle knobs. (C) 5. Fit the cable to the handles with the clips provided. Make sure the cable is not trapped between the upper and lower handles. Locate grassbox upper into grassbox lower. Align clips, ensure all clips are correctly located. Ensure all clips are securely connected. B C D 4 Cutting Height Adjustment · Height of cut is adjusted by raising or lowering the wheels. NOTE All 4 wheels must be adjusted to the same position: HEIGHT OF CUT Low Medium High · WHEELS Hole 1 Hole 2 Hole 3 E · NOTE A medium height of cut is recommended for most lawns. To remove the wheel assembly turn the wheel hub in an anti-clockwise direction. (E) Select one of the 3 holes in the mounting plate and note it as the other 3 wheels will need to be adjusted to the same position. (F) Locate fixing bolt through hole in hub cap, wheel and selected hole in mounting plate. (F) Turn the wheel hub in a clockwise direction until the wheel assembly is securely located to the deck. (E) Using the same height adjustment position repeat the procedure for the other 3 wheels. to remove turn anti-clockwise to fit turn clockwise 1. F wheel 2. 3. mounting plate hub cap 4. 1 2 3 holes fixing bolt 5. Grassbox G Fitting Fully Assembled Grassbox to Lawnmower. Make sure the discharge chute is clean and free from debris. Locate fully assembled grassbox onto 2 location points at the rear of the deck Locate safety flap onto the top of the grassbox. Ensure the grassbox is securely located. AFTER FITTING ENSURE NO GAP REMAINS BETWEEN THE SAFETY FLAP AND THE GRASSBOX. For larger areas of grass where grass collection is not required you can use your lawnmower without the grassbox. The design of the safety flap permits the cut grass to be discharged downward behind the machine. · · 5 Starting and Stopping H J To Start your Lawnmower 1. Form loop in mains cable and push the loop through the slot. [. . . ] DL5 6UP Certify that a sample of the above product has been tested using directive 81/1051/EEC as a guide. The maximum Aweighted sound pressure level recorded at operator position under free field semi anechoic chamber conditions was :I, the undersigned M. Bowden of Electrolux Outdoor Products, Aycliffe Industrial Park, NEWTON AYCLIFFE, Co. DL5 6UP Certify that a sample of the above product has been tested using ISO 5349 as a guide. [. . . ]