User manual FLYMO ROLLER COMPACT 320

[. . . ] ROLLER COMPACT ROLLER COMPACT 3400 ROLLER COMPACT 340/400 ROLLER COMPACT 4000 For all customer enquiries or for replacement parts, contact:- 0870 609 1901 www. flymo. com customer. services@husqvarna. co. uk Carton Contents ROLLER COMPACT 340//3400/400 lock-off button grassbox lid height adjsutment lever washer bolts lower handle fixing pins Easi Reel cable winder (RC3400 only) nuts handle knobs washer deck cable clips cable winder attachment (RC3400 only) instruction manual spanner /scraper upper handle lower handle Easi-Reel cable spool spacer electric cable with moulded on plug washers bolts lower handle fixing pins ROLLER COMPACT 4000 grassbox lid height adjsutment lever nuts handle knob deck cable clips upper handle lower handle electric cable with moulded on plug spanner/scraper lock-off button spacer instruction manual IMPORTANT !Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:Husqvarna Outdoor Products Customer Service Department direct Telephone : 0870 609 1901 Safety If not used properly this lawnmower can be dangerous!This lawnmower can cause serious injury to the operator and others, the warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this lawnmower. [. . . ] Insert the nut into the handle knob (D1). Ensure the upper handle and the lower handle are aligned correctly. Fit the bolts, washers and handle knobs. (D) 4. Fit the cable to the handles with the clips provided. Make sure the cable is not trapped between the upper and lower handles. E 2 1 F 1 Cable Winder Assembly (E & F) RC3400 only 1. Insert cable winder attachment onto left upper handle as viewed from rear of product (E1). Insert cable winder onto attachment and turn downward to secure. Continue turning the cable winder downward until it can be located onto the top of the lower handle (F1). Cutting Height Adjustment G Adjusting the cutting height 1. Lift the lever out of location and rotate to the desired position. (G) Heights of cut:1 & 2 - low, 3 - medium, 4 & 5 - high H spacer The height of cut can be reduced further by the addition of the spacer provided (H) Always handle blade with care - sharp edges could cause injury. Remove the blade bolt and blade as described in Removing the Blade and Fan 2. Place the spacer between the fan and the blade (H) 3. Replace the blade as described in Fitting the Blade and Fan Removing, Emptying and Refitting the Grassbox J grassbox empty Grassbox Full · As the grassbox fills up, grass will be visible through the window in the lid (J). · When the window is full it is time to empty the grassbox. Emptying the Grassbox · Stop the lawnmower, as described in `To Stop your Lawnmower'and wait until the blade has stopped rotating, BEFORE lifting the grassbox lid. Release grassbox catch and lift grassbox lid (B). Rest grassbox lid against lower handle and remove grassbox (K). Replace grassbox and close grassbox lid. grassbox full K Cut Out Device L Cut out · · IMPORTANT The Roller Compact is fitted with a cut-out device (L) which will prevent the lawnmower from being started until the grassbox lid is firmly close and clicked into place. Do not attempt to use your lawnmower without the grassbox in place or with the lid open. · IMPORTANT INFORMATION M When received from the Manufacturer, the front wheels are in a raised position. Do not switch on this product before removing from the raised position into a desired height of cut. (M) Starting and Stopping N P · Important:- Your lawnmower will not start until the grassbox lid is firmly closed and clicked into place. Connect female extension cable connector to the back of the switchbox. [. . . ] Failures due to the following are not covered, therefore it is important that you read the instructions contained in this Operator's Manual and understand how to operate and maintain your machine: Failures not covered by guarantee * Replacing worn or damaged blades * Failures as a result of not reporting an initial fault. * Failures as a result of sudden impact. * Failures as a result of not using the product in accordance with the instructions and recommendations contained in this Operator's Manual. * Machines used for hire are not covered by this guarantee. [. . . ]