User manual FORD CROWN-VICTORIA-2002

[. . . ] Table of Contents Introduction Instrument Cluster Warning and control lights Gauges 4 10 10 17 Entertainment Systems AM/FM stereo AM/FM stereo cassette AM/FM stereo with CD AM/FM stereo cassette (CD changer compatible) CD changer 22 22 26 33 39 49 Climate Controls Manual heating and air conditioning Electronic automatic temperature control 54 54 56 Lights Headlamps Turn signal control Bulb replacement 63 63 65 65 Driver Controls Windshield wiper/washer control Steering wheel adjustment Power windows Mirrors Speed control Message center 72 72 73 74 75 79 83 Locks and Security Keys Locks Anti-theft system 91 91 91 93 1 Table of Contents Seating and Safety Restraints Seating Safety restraints Air bags Child restraints 104 104 108 122 127 Driving Starting Brakes Traction control/AdvanceTrac Air suspension Transmission operation Vehicle loading Trailer towing Recreational towing 137 137 141 144 146 146 151 152 155 Roadside Emergencies Getting roadside assistance Hazard flasher switch Fuel pump shut-off switch Fuses and relays Changing tires Jump starting Wrecker towing 156 156 157 158 159 164 169 174 Customer Assistance The dispute settlement board Utilizing the mediation/arbitration Getting assistance outside the U. S. and Canada Ordering additional owner's literature Reporting safety defects (U. S. only) 175 178 180 181 182 183 2 Table of Contents Cleaning Cleaning your vehicle Underbody preservation 184 184 189 Maintenance and Specifications Hood Engine compartment Engine oil Battery Fuel information Air filter(s) Part numbers Refill capacities Lubricant specifications Engine data Vehicle dimensions 191 192 192 193 197 206 219 224 225 226 228 228 Accessories Index 231 233 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. [. . . ] If the retractor is not locked, unbuckle the belt and repeat steps two through nine. Check to make sure the child seat is properly secured before each use. Installing child safety seats in the lap belt seating positions 1. To lengthen the belt, hold the tongue so that its bottom is perpendicular to the direction of webbing while sliding the tongue up the webbing. Place the child safety seat in the center seating position. Route the tongue and webbing through the child seat according to the child seat manufacturer's instructions. Insert the belt tongue into the proper buckle for the center seating position until you hear a snap and feel it latch. Make sure the tongue is securely fastened to the buckle by pulling on tongue. Push down on the child seat while pulling on the loose end of the lap belt webbing to tighten the belt. 134 Seating and Safety Restraints 6. Before placing the child into the child seat, forcibly tilt the child seat from side to side and in forward direction to make sure that the seat is securely held in place. To check this, grab the seat at the belt path and attempt to move it side to side and forward and back. There should be no more than one inch of movement for proper installation. Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. Tether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap. The rear seats of your vehicle are equipped with built-in tether strap anchors located behind the seats as described below. The tether anchors in your vehicle are located under a cover marked with the tether anchor symbol (shown with title). The tether strap anchors in your vehicle are in the following positions (shown from top view): Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor. Position the child safety seat on the seat cushion. Route the child safety seat tether strap over the back of the seat. [. . . ] Refer to your scheduled maintenance guide to determine the correct service interval. 1 227 Maintenance and Specifications ENGINE DATA Engine Cubic inches Required fuel Firing order Spark plug gap Ignition system Compression ratio VEHICLE DIMENSIONS Vehicle dimensions (1) Overall length (2) Overall width (3) Overall height (4) Wheelbase (5) Track - Front (5) Track - Rear a Denotes long wheel base mm (in) 5 386 (212)/5538 (218)a 1 987 (78. 2) 1 443 (56. 8) 2 913 (114. 7)/3066 (120. 7)a 1 611 (63. 4) 1 659 (65. 3) 4. 6L V8 engine 281 87 octane 1-3-7-2-6-5-4-8 1. 3-1. 4 mm (0. 052-0. 056 inch) Coil on plug 9. 4:1 3 5 2 228 Maintenance and Specifications 4 1 IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver's side. MFD. IN U. S. A. DATE: XXXXX GVWR:XXXXXXXXXXXX FRONT GAWR: XXXXXX/XXXXXXX REAR GAWR: XXXXXXX/XXXXXXX THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL MOTOR VEHICLE SAFETY, BUMPER, AND THEFT PREVENTION STANDARDS IN EFFECT ON THE DATE OF MANUFACTURE SHOWN ABOVE. VIN: XXXXXXXXXXXXXXXXXX XXXXX TYPE: XXXXXXXXXXXXXXX XXXXX EXT PNT: XXXXXX XXXXXX RC: XX DSO: XXXX BAR INT TR TP/PS R AXLE TR SPR X XX XXX X XX X XXXX UPC F85B-1520472-AB 229 Maintenance and Specifications Vehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. [. . . ]