User manual FOSSIL T205

[. . . ] The memory card version is very easy to use. Read the Quick Start Guide first and start using FOSSIL Navigator right away. This document is the detailed description of the software. Although FOSSIL Navigator can easily be discovered by experience, it is still recommended that you read through this manual to clearly understand the exact function of each button and icon. Table of contents 1 2 3 Warnings and safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Operating Naviio Navigator (Controls). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3. 1. 1 Tilt up and down. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This is normally shown together with the primary name in this field. You can hide these alternative names in Map settings (5. 2. 3). 4. 5. 15 Travel and Route data (No. 17) The contents of these three fields are different when cruising (without an active route) or navigating (following an active route). While cruising, the fields show the present speed, the current speed limit and the time of day. You can choose what to display in these three fields during navigation, by going to Advanced settings / Display Options (5. 6. 1). See the following list for your options. The only restriction is that you cannot select a value that already appears in another field. The possible field contents are: · · · · · · · 38 Distance to destination (default value for the left field) Time to destination (estimated time en route, default value for the middle field) Distance to next via point Time to next via point Time to next maneuver (next route event) Speed Speed limit · · Arrival at next via point Arrival at destination (default value for the right field) 4. 5. 16 Distance to next turn (No. 18) This field shows the distance to go before reaching the next route event (turn, roundabout, exit, etc. ) This field is only displayed when navigating a route. 4. 5. 17 Next street / Next settlement (No. 19) This field shows the road or street that comes next in the route itinerary. If you are not yet in the settlement where this next street is, FOSSIL Navigator will display the name of the settlement instead of the name of the road or street. It either displays the `Route' or the `Vehicle' field from the Route parameter settings. If you have chosen Car, Taxi, Bus or Lorry, the type of the route (Fastest, Shortest or Economical) will be displayed here; if you have selected Emergency, Bicycle or Pedestrian, this information will be displayed here. 4. 6. 1. 4 Time Left This is an estimated value that can also be displayed in one of the Route data fields on the Cockpit screen as `Time to destination'. It shows the time needed to reach the final destination of the route based on information available for the remaining segments of the route. The calculation cannot take into account traffic jams and other possible delays. If via points exist, tap and tap again any of the fields to see the time needed to reach the first, second, etc. 4. 6. 1. 5 Estimated Arrival This is an estimated value that can also be displayed in one of the Route data fields on the Cockpit screen as `ETA to destination'. It shows the time needed to reach the final destination of the route based on information available for the remaining segments of the route. The calculation cannot take into account traffic jams and other possible delays. If via points exist, tap and tap again any of the fields to see the estimated arrival at the first, second, etc. 4. 6. 1. 6 Destination / Via point This field shows the exact address (or its coordinates if the address is not available) of the final destination. [. . . ] On this screen you can see the first page of the top level POI categories. There are three levels altogether. The search will be carried out around a certain reference point. Always look at the current reference point shown in the green field above the POI category buttons and confirm that it matches what you want. To change the reference, tap the Change ref. [. . . ]