User manual FOSTEX 8338

[. . . ] External time code (LTC) input will be displayed as the Reference!. . . . . . . . . . . . . . . . . 8 3. Input monitor of audio/time code is possible!. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Changes and the new effective SETUP menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 1. Version display function [vErSion 001 -chk]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2. Setup of the playback time code format [ReProtc 401 -***]. . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3. [. . . ] Then, after rotating the [JOG] dial CW and CCW to select the desired frame rate, press the [EXECUTE/SET] key again (* is the initial setting). This setup content will be held even if the power is switched OFF. Functional note Fr 29. 97 Fr 30 Menu No. 000 (*) 001 Functional content The 29. 97fps time code is selected. The 30fps time code is selected. 13 Model 8338 (TC/SYNC card) Owner's Manual 8. Setup of the CHASE operation mode [CH SE M od 501 -***] The mode for locking (chase locking) D-15 to the external time code is selected by this menu. Operating modes can be selected from "oncE, " "Cont" or "FrAME. " After entering the SETUP mode, rotate the [JOG] dial, select the [CHSEMod 501 -***] menu, and press the [EXECUTE/SET] key. Then, after rotating the [JOG] dial CW and CCW to select the desired frame rate, press the [EXECUTE/ SET] key again (* is the initial setting). This setup content will be held even if the power is switched OFF. Functional note oncE Menu No. 000 (*) Functional content After CHASE ON of D-15, chase is ended upon locking once on REF TC, then D-15 will free run. Also, even if lock is disengaged, it will not enter chase again. After CHASE ON of D-15, it will lock onto REF TC, then will free run. Connect the external equipment time code (LTC) output to the TIME CODE IN (XLR-3-31 type or RCA) connector of 8338 installed in D-15. <NOTE> If cables are connected to both XLR (balanced) and RCA (unbalanced) connectors, RCA will have priority and thus XLR cannot be used. If XLR must be used, do not plug anything in the RCA jack. 2. Connect the audio input to the D-15 DIGITAL IN (or ANALOG IN) connector. Other audio equipment LTC OUT Time code generator WORD IN 75 OUT 75 IN VIDEO THRU IN OUT TIME CODE IN OUT ON OFF ON OFF ANALOG INPUT CH2 CH1 CH2 CH1 ANALOG OUTPUT CAUTION UNBAL BAL CH2 CH1 CH2 CH1 AC IN IN OUT IN DIGITAL I/O OUT GPI IN GPI OUT 37P-REMOTE D-15 + 8338 AES/EBU OUT OPTICAL OUT Other DAT, etc. 16 Model 8338 (TC/SYNC card) Owner's Manual Recording 1. Set the D-15 front panel [CLOCK] switch to [INT]. When an external sync signal is input as a reference to record the time code in sync with this sync signal, set the [CLOCK] switch to [EXT] using the SETUP menu "503 -***. " Set it to the external clock identical with the external sync signal (Refer to <NOTE> below). Refer to page [15] for setup of the SETUP menu "503 -***. " 2. Setup the frame rate by the SETUP menu "411 -***" when time code to be recorded is 29. 97fps or 30fps. When recording the 24fps, 25fps time codes, they will be automatically acknowledged and recorded regardless to the setting of the SETUP menu. The D-15 will automatically acknowledge 24 and 25fps time codes and record them but 29. 97 and 30fps cannot be acknowledged. Therefore, if 29. 97 or 30fps time codes are to be recorded, they must be specified by the SETUP menu "411 -***. " Refer to page [13] for setting by the SETUP menu "411-***. " 3. Start the externally connected audio equipment and the TC generator. Start the D-15 in the record mode by pressing the [PLAY] button while pressing the [RECORD] button. 5. After completing the recording, press the [STOP] button. <NOTE> Because ASSEMBLE recording only can be made by the D-15, if recording is temporarily stopped and then resumed, continuous time code cannot be recorded. <NOTE> If a recording is made with the [CLOCK] switch at [INT], a slight deviation of the clock will be created between the recorded time code (LTC) and the inner sampling clock. In such a case, synchronize the entire system by input of an external video sync signal as a reference to the VIDEO IN connector of this equipment. 17 Model 8338 (TC/SYNC card) Owner's Manual 2. [. . . ] For example, when attempting to locate to the MEM NO stored in TC time in the memory, if this is executed while A-TIME is displayed, the TC time for locating will be by the A-TIME and thus be located by this time. 25 Model 8338 (TC/SYNC card) Owner's Manual 7. Editing the OFFSET Figure By installing the 8338, it will then be possible to edit memory data of TC time aside from A-TIME. The same method as when an 8338 is not installed can be used by changing the display to TC. In addition, editing CHASE OFFSET is now possible as a new function. [. . . ]