User manual FOSTEX A-4

[. . . ] Acts the same as the [FILE SEL] key on the panel. Selects the "Select drive" menu item in the Setup menu. Acts the same as the [CUE] key on the panel. Enters the Utility mode. 5) The new "False Start" menu item is added to the Setup menu. The new "False Start" menu item added to the Setup menu allows you to select whether deleting or keeping the file after executing False start. [. . . ] The TC frame changes only when the clock is pulled down. The TC frame changes when the clock is pulled up or down. The TC frame changes only when the clock is pulled up. The TC frame changes only when the clock is pulled down. The "drive select" function has been added from V2. 00. See the "Version 2. 00 supplementary manual" for details about this function. Before V2. 20 From V2. 20 24 25 The "Select drive" screen when no drive option is installed 29. 97DF / ND 30DF / ND 29. 976 The "Select drive" screen when no drive option is installed. A "Select drive" screen example when the Model 9056 (Internal hard disk) is installed and the A-4 DVD-RAM is selected You can select from among the A-4 DVD-RAM drive (iDVD) and HDD partitions (iP01 through iP27). A "Select drive" screen example when the EX-12 is connected and the EX-12 DVD-RAM is selected You can select from among the A-4 DVD-RAM drive (iDVD), EX-12 DVD-RAM drive (eDVD) and EX-12 hard disk partitions (iP01 through iP08). When the Model 9056 optional hard disk drive in installed and the EX-12 is connected to the A-4, you can select from among the A-4 DVD-RAM drive (iDVD), internal hard disk partitions (iP01 through iP27), the EX-12 DVD-RAM drive (eDVD) and EX-12 hard disk partitions (eP01 through eP08). 4 213 Model A-4 operation manual (Supplement for V2. 20) Model A-4 operation manual (Supplement for V2. 20) Enhancement of the "Format" menu item in the UTILITY menu The "Format" menu item is used for formatting a DVD-RAM disk set to the A-4 or the optional EX-12, or a partition of the optional internal hard disk or the optional EX-12. In this menu item, the following three changes has been made. Ubit information display capability on the Normal screen The new "Repro Ubit" option is added to the time display modes on the Normal screen. You can switch the time display mode among the following using the [TIME/DISP MODE] key. LTC <Before V2. 20> LTC IN GEN ABS · You can now select on or off of the physical format when "Mirror" is selected as the Format mode. With the earlier software version, you can select on or off of the physical format only when "Normal" is selected as the Format mode. With the new version, you can select on or off of the physical format even when "Mirror" is selected as the Format mode. See the table below for details about the available options. See also the V2. 00 supplementary manual for "Set Gen. TC" menu item setting when the "Gen mode" is set to any option other than "Free Run". While the [SHIFT] indicator is lit, press the [CONTRAST/TC SETUP] key to enter the TC SETUP menu. Then use the [SEL] dial to highlight "Set Gen. The display now shows the "Set Gen. TC" screen on which you can see the generator time code value in realtime. Enhancement of the "Default file name" menu item in the Setup menu The "Default file name" menu item in the Setup menu is enhanced by adding the "Reel mode" option to the default file name mode. Therefore, there are now three options for file name mode selection: "Date", "Scene name + Take No. " and "Reel No. See also "Default file name setting (Default file name)" on page 99 in the A-4 operation manual. Press the [SETUP] key to enter the Setup menu, and use the [SEL] dial to select the "Default file name", then press the [ENTER] key. · Setting the file name mode By pressing the [ENTER] key when the screen above right is shown, the currently selected mode starts flashing and you can now select the desired mode (the default mode is "Take"). Use the [SEL] dial to select the desired mode and press the [ENTER] key to confirm your selection. · Editing the generator time code value, : While this screen is shown, press the [ENTER] key. The frame field starts flashing and you can now edit the displayed time code. Flashing Flashing Take (Default) "<SCENE NAME>_<TAKE NUMBER>. wav" is the default file name. [. . . ] You can now select the desired mode. Flashing 2) Use the [SEL] dial to highlight "Chain Play" and press the [ENTER] key. The currently selected mode starts flashing (by default, "Off" is selected). You can now select the desired mode. 3) Use the [SEL] dial to select the desired mode and press the [ENTER] key. You can select between "Rename" (default) and "Delete". When the False start function is executed, the take number decreases by one (i. e. returns to the previous take number) and the canceled audio file is stored as a file with the file name starting by "~nn" followed by the original name ("nn" shows the number). [. . . ]