User manual FOSTEX AP3090

[. . . ] ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosurethatmaybeofsufficientmagnitudetoconstitutea risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. "WARNING" "TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. " SAFETY INSTRUCTIONS 1. 5. 6. Read Instructions - All the safety and operating instructions should be read before the appliance is operated. Retain Instructions - The safety and operating instructions should be retained for future reference. [. . . ] In the brightness adjustment mode, meter selection mode or status display mode, this key acts as the [EDIT] key (see page15). Pressingthiskeybrieflyexitsthecurrentmode while pressing this key for a second or more enters or exits the parameter editing mode. 1/4-inch [PHONES] jack You can connect stereo headphones with the 1/4-inch plug for monitoring. Headphones level control This control is used to adjust the output level of both the 1/4-inch and mini [PHONES] jacks. [LIMITER] switch (ON, OFF, LINK) This switch enables or disables the limiter function. The limiter can work individually or in link, as described below. The limiter circuit is inserted after the MASTER fader. LINK The limiter function is enabled with the left and right channels linked. If either of left and right channel signals exceeds the threshold, both the left and right channel limiters work in the same way. Each of the left and right limiters works independently. The limiter function is disabled (the limiter circuit is bypassed). "LIM" icon "LIM" icon 15. [MASTER] faders (L and R) These faders control stereo left and right buss output levels. The scale position in orange shows the reference position. Pressing a fader puts it to the up position. Connector: XLR-4-32 type (male) 1 2 4 3 GND NC DC 10-24V NC 3. [TO ST BUSS] switch (ON / OFF) This switch selects whether or not the input signal from the [AUX IN] connector is sent to the stereo buss. To send the [AUX IN] signal to the stereo buss, set the switch to ON. When the switch is set to OFF, the [AUX IN] signal is not sent to the stereo buss. Regardless of the switch setting, you can monitor the [AUX IN] signal via headphones. Input select switches (LINE / MIC) Each switch should be set appropriately according to the input signal source. LINE You should set the switch to LINE when a line-level source is connected to the input connector. When it is set to LINE, the microphone power supply is automatically turned off regardless of its setting. You should set the switch to MIC when a microphone is connected to the input connector. You can supply the microphone power when connecting a condenser microphone (see "Microphone power supply switch" below). 7. [DC OUT 7. 2-24V] connector This connector outputs power at DC 7. 2 ~ 24 V / 0. 5 A for a wireless receiver, etc. It outputs power when the unit is powered on. Connector: Hirose 4-pin HR10A-7R-4S (female) 1 2 4 3 GND NC DC7. 2 to 24V NC 4. MIC 12 Right side panel section 1. [MAIN OUT] (L, R) connectors These connectors output stereo buss L and R signals. You can select the output reference level using the MAIN OUT level select switch described below. [. . . ] Labor costs are also covered by Fostex America for one (1) year from the date of original purchase. Except as specified below, this warranty covers all defects in material and workmanship in this product. The following are not covered by this warranty: 1. Damage to any product that has been altered. [. . . ]