User manual FOSTEX D-108

[. . . ] Owner's Manual Model 8288 421 000 8 Track Digital Recorder AUTO RTN AUTO PLAY CLIPBOARD IN OUT START AUTO PUNCH IN OUT END DISP SEL EXECUTE /YES EXIT /NO 8 TRACK DIGITAL RECORDER AUTO RTN COPY MOVE PASTE ERASE UNDO REDO TIME BASE SEL HOLD/ STORE RECALL POWER PGM SEL AUTO PUNCH REHEARSAL TAKE OPTICAL PREVIEW LOCATE VARI PITCH 1/9 PUNCH IN / OUT 2/10 3/11 4/12 RECORD TRACK 5/13 6/14 RECORD 7/15 8/16 SHIFT ENVELOPE STOP PLAY REWIND F FWD LOCKED HD ACCESS TC IN CLIPBOARD PLAY LOCATE ABS 0 LOCATE REC END D-108 Owner's Manual (Safety Instructions) CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION: CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. "WARNING" "TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. " SAFETY INSTRUCTIONS 1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated. [. . . ] While the recorder section is stopped, press and hold down the RECALL key and press the memory key for which you wish to check the edit point. You can preview "fade-out" at the AUTO PUNCH IN point and "fade-in" at AUTO PUNCH OUT point. · To erase the data in its entirety from the tracks, you can also use the Program Delete function to erase the entire Program. In either case, you can expand the recordable area on the disk. Use either one of the erase operations to erase unnecessary data if the D-108 displays an alarm message indicating insufficient recordable space for Auto Punch In/Out, Copy & Paste, or Move & Paste. · To erase the data in its entirety from ABS 0 - REC END, it is recommended that erase end point (AUTO PUNCH OUT point) is stored after the REC END time to ensure thorough erase performance. To do this, move the recorder section location to the REC END point prior to storing the AUTO PUNCH OUT point, press the PLAY button from that location, move the ABS time after the REC END, and store. The hard disk will not successfully access points after REC END though play is executed after REC END, however, this makes it possible to move up the ABS time. 2. Trim the edit point while previewing. ·Refer to "Preview Function" on page 65 for more information. Executing Erase 1. Press the RECORD TRACK select key to select the track to erase, to set it READY. You can select a mono track or multiple tracks (including all 8 tracks). The selected track indication flashes. 2. Press the ERASE key. [Erase] appears on the display, and [SURE?] flashes. The track indication lights up. 71 D-108 Owner's Manual (Editing Tracks) Undo/Redo Erase You can undo or redo the Erase operation. · To restore the data that existed before you erased it, press the UNDO key. · To restore the data after you undo the Erase operation, press the REDO key again. When you press the UNDO or REDO key, the D-108 will undo or redo the operation immediately, and display [Undo !] or [Redo !] and [COMPLETED !]. Note: The Undo/Redo function is effective only when the D-108 is stopped. Note: If you perform one of the following operations after you use the Copy & Paste or Move and Paste operation, the Undo/Redo function will no longer be effective. 1. When a new editing is executed (such as Copy & Paste, Move & Paste, Erase). While in the AUTO PUNCH ON mode, when the AUTO PUNCH IN point is passed in the PLAY (or RECORD) mode. When the power is momentarily switched off. When ejecting a removable SCSI disk that is the current drive. Erase all data of a voluntary program (Program Erase) Here we will erase unnecessary data on all tracks that are recorded on specific programs. The erase procedure conducted here varies from the "Erasing a Program" procedure described in "Program Operations" mentioned earlier. Here, instead of erasing the program itself, the data in all tracks are erased, while the program remains intact. After erasing the data, that program goes to the default status as when creating a New Program. [. . . ] * "Adat" and the symbol are trademarks of OPTICAL :D-sub 25 pin (X1) Alesis Corporation. * FDMS-3: Fostex Disk Management System-3. * FDIO-1 Ver. 2: Fostex Data In Out-1 Ver. 2 PUNCH IN/OUT Connector : Ø6mm Phone jack (X 1) (An optional FOOT SW Model 8051 can be connected. ) REMOTE Connector : D-sub 15PIN (X 1) Recording/Reproducing Recording medium : 3. 5 inch, hard disk (EIDE type) or External SCSI device : FDMS-3* : FDIO-1 Ver. 2** : 44. 1kHz/48kHz Recording format Save/Load format Sampling frequency Quantization : 16-bit linear (Non expanded) A/D: 20-bit 64-time, over sampling, Delta-Sigma D/A: 20-bit 128-time, over sampling, Delta-Sigma No. of recording track : 8 + 16 Additional tracks (for 8track format) Program No. [. . . ]