User manual FOSTEX D-160

[. . . ] D-160 Owner's Manual (Introduction) Owner's Manual Model Digital Multitrack Recorder 1 D-160 Owner's Manual (Introduction) CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. "WARNING" "TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. " SAFETY INSTRUCTIONS 1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated. Retain Instructions - The safety and operating instructions should be retained for future reference. [. . . ] Rotate the JOG dial to select a Program to save. You can select any existing Program (up to 99) to save. 7. Press the EXECUTE/YES key. The duration of the selected Program appears on the display so that you can edit the time shorter or longer, as necessary. Time length recorded in the selected program will be displayed and the time can now be edited. Normally, it is saved in the time displayed but at this stage, it is also possible to save in any shorter time or by setting the time longer than what is actually recorded. This function is provided for the purpose of saving in a short section of insufficient tape capacity. Maximum saving time is 60 minutes. 8. Press the EXECUTE/YES key again. "Save Trk?1-16" ("1" is flashing) appears on the display and you can select tracks to save. While "1" is flashing, rotate the JOG dial to select "1"->"9"->"17. " To select "8"->"16"->"24, " use the SHUTTLE or press the HOLD/> key to flash "16" and rotate the JOG wheel. You can select one of the following track combinations: "1-8, " "1-16, " "1-24, " "9-16, " "17-24. " (Tracks 17-24 are additional tracks. Selecting "1-24" or "9-24" will cause the additional tracks to be saved along with the real tracks. ) 9. Press the EXECUTE/YES key. "Rec Start DAT!" (Start recording on the DAT) or "Rec Start adat!" (Start recording on the adat) appears on the display, and "SURE?" flashes. 10. Confirm that the external device is syncing with the digital input signal, and start recording on the external device (DAT or adat). Setting a START-ID (DAT) or a locate point at the recording start point will facilitate future loading operations. 11. Confirm that the recording on the external device has started, and press the EXECUTE/YES key. ("REMAIN" will light. ) The save operation starts, and the time required for the save operation appears on the display and a few seconds later, it will start counting down. This few seconds delay is due to the pilot signal which is recorded to mark the beginning of the Program to facilitate future load operation. Therefore, the actual save operation starts when counting down starts. Two tracks are saved each time in the order of Track 1 and 2, 3 and 4, etc. Eight tracks are saved each time in the order of Track 1-8, 9-16, etc. The level meter indication during save of DAT will always be for only tracks 1 and 2 and always for tracks 1~8 in save of adat. 12. When the save operation is complete, "COMPLETED!" flashes on the display. Press the STOP button or the EXIT/NO key to quit the Setup mode. [. . . ] 32W Weight Power supply Power consumption * Specifications and appearance are subject to change without notice for product improvement. * "Adat" and the symbol are trademarks of Alesis Corporation. * FDMS-3: Fostex Disk Management System-3. * FDIO-1 Ver. 2: Fostex Data In Out-1 Ver. 2 190 D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications) INDEX [A] About copy rights 8 About damages 8 Auto play/Auto return key Auto punch mode ON/OFF key Auto punch in key 16 Auto punch out key 16 Auto return start key 15 Auto return end key 16 ABS time display 26 ABS 32, 38 Audio file 33 Additional track 36 Analog recording 53 Auto play mode 70 Auto return mode 70 Auto repeat mode 74 Auto punch in/out 76 Erasing 96, 99, 101 Entering Setup mode 15 20 137 [F] Fast forward button Formatting the hard disk Formatting a SCSI disk Frame rate setting 22 39, 43, 171 109 151 [H] Hold/Digit move key Hard disk operation LED Hard disk recording Hard disk 39 18 13, 23 32 [I] Introduction 6 Input jack 23 Input monitor 37 Installing a hard disk Inquiry message list [B] Basic connections Backup 111 46 39 173 [J] Jog dial 18 [C] Clipboard in key 15 Clipboard out key 15 Copy key 20 Connecting a digital mixer 65 Changing the stored the start/end point 73 Copy and Pasting 88 Copying 86 Copy and paste undo/redo 90 compatibility with D-90, D-80 ver2 etc. display 30 Lock/unlock key 40 Locate function 67 Loading the data 102, 106 [M] Main features 9 Meter display 25 MIDI IN connector 24 MIDI OUT connector 24 MIDI THRU connector 24 MTC display 27 MTC 38 Mixdown 58 Moving 91 Move & pasting 93 Move & paste undo/redo 95 MIDI clock synchronization system MTC synchronization system 120 Multitrack system by the slave mode Multitrack system using a DMT-8 V2. 0 Metronome function ON/OFF 148 MIDI SYNC OUT setting 150 MTC frame rate setting 151 MTC OFFSET time setting 152 MTC OFFSET MODE setting 153 MIDI device ID setting 161 MIDI implementation chart 172 MMC command list 173 Maintenance 189 [D] Display section 25 Dust cap 8, 39 DISK REMAIN display 26 Disk Error !display 30 Disconnect SCSI display 31 Default setting on the D-160 Deleting program 51 Digital recording 60 Display select key 17 DATA IN connector 23 DATA OUT connector 24 48 117 123 133 [E] Erase key 19 Execute/Yes key 17 Exit/No key 17 Event Over ! [. . . ]