User manual FOSTEX UR-2

[. . . ] 8289647000 (480799) Model UR-2 STEREO RACK MEMORY RECORDER POWER AUTO PLAY PHONES EDIT USB (KYBD ONLY) PC USB HOST SD-1 MIN MAX SD-1 SD-2 EJECT READY SD-2 FILE SEL REPEAT REC DISPLAY MRGN RST STOP PLAY PREV REW CUE NEXT F FWD TIME EDIT MIC SET SHIFT PLAY MODE MENU / ENTER TIME REC RDY EXIT FILE/CURSOR CUE/LOCATE MIC IN PHANTOM UR-2 STRG SEL STEREO RACK MEMORY RECORDER ABS 0 REC END MIN MAX MIN MAX INPUT LEVEL MIC GAIN MIC IN Owner's Manual Model UR-2 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. "WARNING" "TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. " SAFETY INSTRUCTIONS 1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated. [. . . ] Even if you edit a file name, the playback order does not change. <Memo>: When playing back a file, you can mix a microphone signal and output the mixed signal (see page 38). -43- Model UR-2 <Playback> Playback in CHAIN SINGLE play mode When you select the CHAIN SINGLE play mode, " lights on the display, while the " unit reads the chain play list information and stops at the beginning of the first file in the list. Playback in CHAIN ALL play mode When you select the CHAIN ALL play mode, " " lights on the display, while the unit reads the chain play list information and stops at the beginning of the first file in the list. <Note>: When no chain play list is created, "CHAIN LIST Empty!" is briefly shown followed by the following screen. In this case, create the chain play list and select the CHAIN SINGLE play mode again. See page 46 for details about how to create the chain play list. <Note>: When no chain play list is created, "CHAIN LIST Empty!" is briefly shown followed by the following screen. In this case, create the chain play list and select the CHAIN ALL play mode again. See page 46 for details about how to create the chain play list. In the CHAIN SINGLE play mode, the unit plays back a selected file in the chain play list. After finishing playback, the unit stops at the beginning of the next file. To play back a different file, select a desired file using the [ ] or [ ] key, or using the file selection screen (see page 42). <Memo>: By activating the repeat function, you can play back a file repeatedly until you stop by pressing the [STOP] key (see page 54). In the CHAIN ALL play mode, the unit continuously plays back all files in the chain play list from the first file. After finishing playback of the last file in the chain play list, the unit stops at the beginning of the first file. To start playback from a desired file, select the ] or [ ] key, or using the file file using the [ selection screen (see page 42). <Note>: When the unit switches the playback file, if the next file has different FS/bit, it takes some time to switch the file. Therefore, there is a silent space between files. <Memo>: You can mix a microphone source while playing back a file. You can also output the microphone signal alone while the unit is stopped. (See page 38. ) <Memo>: You can mix a microphone source while playing back a file. You can also output the microphone signal alone while the unit is stopped. (See page 38. ) <Memo>: By activating the repeat function, you can play back a file repeatedly until you stop by pressing the [STOP] key (see page 54). -44- Model UR-2 <Playback> Playback in MEMORY play mode When you select the MEMORY play mode, the unit reads the play list information and shows the MEMORY PLAY MODE screen as below. Playback in TIMER play mode When you select the TIMER play mode, the unit reads the play list information and shows the timer play screen something like below. <Note>: If the list is not created, "CHAIN LIST Empty!" is shown followed by the screen as below. In such a case, create the play list and then select the MEMORY play mode again (see page 46 for details about how to create the play list). <Note>: If the list is not created, "TIMER LIST Empty!" is shown followed by the screen as below. In such a case, create the play list and then select the TIMER play mode again (see page 51 for details about how to create the play list). In the MEMORY play mode, you can perform instant start of up to ten files in the play list from a USB keyboard. The memory numbers 1 through 10 in the MEMORY PLAY MODE screen are assigned to the numeric keys on the keyboard. Pressing a numeric key starts playback of the file set to the corresponding memory number. Memory number 10 is assigned to the "0" key. For example, if you press the "4" key of the USB keyboard, the file set to memory number 4 starts playback instantly and the display shows the screen as below. At the top of the screen, the playback elapsed time is shown. In the TIMER play mode, the unit starts playback of the files in the list. [. . . ] Damage to any product on which the original serial number has been defaced, modified or removed. Damage to or deterioration of the external cabinet. Damage occurring during shipment of the product. (NOTE: Shipping claims must be presented to the carrier. ) Damage resulting from accident, misuse, abuse or neglect. [. . . ]