User manual FOSTEX VF160EX

[. . . ] 8588 044 000 (396678) Digital Multitracker INPUT 1/9/A 2/10/B 3/11/C 4/12/D 5/13/E 6/14/F BAL 7/15/G UNBAL INSERT BAL 8/16/H UNBAL MON OUT INSERT L R PHONES TRIM MON OUT PHONES LINE MIC PEAK LINE MIC PEAK LINE MIC PEAK LINE MIC PEAK LINE MIC PEAK LINE MIC PEAK LINE MIC PEAK LINE MIC PEAK 0 10 0 10 1/9/A 2/10/B 3/11/C 4/12/D 5/13/E 6/14/F 7/15/G 8/16/H CH STATUS/CH SEL CH STATUS ORANGE INPUT RED REC GREEN PLAY OFF MUTE RECALL SCENE STORE CLEAR OPTICAL DIRECT RCL MAP EFF EDIT EFF1 EFF2 ACCESS ACCESS +6 +6 MUTE 0 0 MUTE PHANTOM PHANTOM EQ/COMP HI-G/F/Q EFF1/EFF2 PRE/POST -10 -10 COMP INPUT SEL AUX1/AUX2 MID-G/F/Q REC ASSIGN BUSS REC TRK SOURCE DIRECT REC TRK INT MIXDOWN DISP SEL PGM SEL SETUP -20 -30 -40 -50 -60 -20 -30 -40 -50 -60 PRE/POST START PAN LO-G 1 FADER CH VIEW HOLD/ 2 AUTO RTN AUTO PUNCH IN OUT TIME BASE END IN CLIPBOARD ALIGN SEL OUT A RTN A PLAY - - 3 4 MARK UNDO /REDO 5 6 VARI PITCH 7 SCENE SEQ. CH PARAM EDIT STORE EDIT LOCATE SCRUB 1 CH STATUS/CH SEL 2 3 CH STATUS ORANGE 4 INPUT 5 RED REC 6 GREEN PLAY 7 OFF 8 MUTE TRACK P. EDIT EVT MEM CD PLAY RECORD STOP PLAY REWIND F FWD AUTO PUNCH +6 +6 +6 CLIPBOARD PLAY LOCATE ABS 0 LOCATE REC END PREV NEXT 0 0 0 FADER ADJUST -10 -10 -10 EXIT/NO LEVEL ADJUST -20 -30 -40 -50 -60 -20 -30 -40 -50 -60 -20 EJECT ENTER/YES -30 -40 -50 -60 - - - SHIFT JOG SHUTTLE 9 A 10 B 11 C 12 D 13 E 14 F 15 G 16 H TRACK INPUT MASTER Operation Manual CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. "WARNING" "TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. " SAFETY INSTRUCTIONS 1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated. [. . . ] As shown in the figure below, there are five programs from P01 to P05. Note that the program numbers always remain in sequential order. Therefore, when program number P03 is erased, there will only be a total of 4 programs. This means though the data on P03 is erased, and the numbers are sequentially corrected (no number is skipped). Note that only the contents of P03 are erased and the numbers are merely reassigned in sequential order according to the number of programs available. Simply put, P04 becomes P03 and P05 becomes P04, when P03 is erased, as in this case. P01 P02 P03 Delete P03 P04 Flashing Editing a Program Title Note that the program title can be assigned when "Creating a New Program" as described in the previous section. However, the user must follow the instructions below to edit a title (or Tentative Title) that has already been assigned. <Precaution> Note that only the title of the program that is started up can be edited. The user cannot choose a program from the SETUP mode. Therefore, the user must first start the program to edit, before going to the SETUP mode. 1. Press the [SETUP] key in the STOP state. The system goes to the SETUP mode and proceeds to the display to select a SETUP menu. 2. Turn the [JOG] dial to select the "Title Edit" menu, then press the [ENTER/YES] key. The title (name) of the current program started appears. The left end of the title is highlighted and flashes. (the flashing cursor indicates that it is editable) P04 P05 P01 P02 · Remember that it is not possible to UNDO/REDO (unerase or re-erase) the ERASE feature once a program is erased. 71 3. Press the [REWIND] key or [F FWD] key to move the cursor to the point to edit. Then turn the [JOG] dial to choose the alphanumeric/symbol to input. The title can contain up to 16 characters form the following alphanumerics and symbols. 4. Press the [ENTER/YES] key after inputting the title. The title input is set and the LCD returns to the Normal Display. Editing the Track The VF160EX features a 3. 5 inch E-IDE hard disk as a storage media. This allows speedy voice editing in a nonlinear and nondestructive manner in track units. There are four track editing options as described below. Copy & Paste A specific range of data on a voluntary track can be copied and then pasted to the same track or another track. Note that the Copy & Paste feature is only possible with the current program started. Track Exchange Tracks are interchangeable with each other. Mono tracks or several (2 track or 8 track unit) tracks are exchangeable, to freely exchange between the 24 real tracks and additional tracks. Note that the Track Exchange feature is only possible with the current program started. Move & Paste A specific range of data of a voluntary track can be moved and pasted to the same track or another track. [. . . ] In a sampling frequency other than 44. 1kHz/16 bit, it will be recorded with the wrong pitch. Time count will also be incorrect. Having trouble Editing? · A warning message appears although it was only execution of copy-clip (or move-clip) ? Correctly register the CLIPBOARD IN and OUT points. The relation between CLIPBOARD IN point and OUT point is "IN point<OUT point". If it is registered in reverse relationship, copy-clip (or move-clip) cannot be executed. · When copy paste (or move paste) is executed, the sound section located before head of the bar is missing? Use the ALIGN SEL function. If the "ALIGN SEL" function is used at executing copy paste (or move paste), the sound section located in front of the bar head can be included at pasting. Refer to page 74 for details. 150 MIDI Implementation Chart (Digital Multitracker) Model VF160EX Function. . . . . . . . . . . . . . . . . . . . [. . . ]