User manual FOSTEX VM200

[. . . ] VM200 DIGITAL RECORDING MIXER USER'S GUIDE INPUT 1 INPUT 2 INPUT 3 INPUT 4 INPUT 5 INPUT 6 INPUT 7 INPUT 8 MONITOR PHONES A B PAD 26dB TRIM A B PAD 26dB TRIM A B PAD 26dB TRIM A 2TRK IN B PAD 26dB TRIM TRIM TRIM TRIM TRIM GAIN GAIN -16 +10 -60 -34 -16 +10 -60 -34 -16 +10 -60 -34 -16 +10 -60 -34 -10 -50 -10 -50 -10 -50 -10 -50 MIN MAX MIN MAX METER OL -3 -6 -9 -12 -18 -24 -36 -48 L R ST BUSS/SOLO DIGITAL RECORDING MIXER VM200 PAGE SELECT 1-8 ANALOG IN 9-16 ADAT IN 17-20 EFF RTN SETUP SYSTEM MIDI EQ/LO GAIN EQ/LO-MID GAIN EQ/HI-MID GAIN EQ/HI GAIN SELECTED EQ EQ ON EFF1 EFF EDIT EFF2 EQ LIBRARY CURRENT SCENE STATUS FREQ Q FREQ Q FREQ Q FREQ Q RECALL STORE RECALL EFF LIBRARY STORE PAN PAN PAN PAN PAN PAN PAN PAN EQ EDIT KEY MODE ROUTING/ PHASE PAIR/ GROUP EQ EDIT EQ EDIT EQ EDIT EQ EDIT EQ EDIT EQ EDIT EQ EDIT REC BUSS SOLO MMC SEND CHANNEL/ METER SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SCENE MEMORY RECALL STORE CH VIEW ON ON ON ON ON ON ON ON ON FADER MODE AUX1 AUX2 /-1 +1/ AUX3 AUX4 +10 +10 +10 +10 +10 +10 +10 +10 0 EXIT DATA ADD. AUX 0 EFF1 EFF2 0 0 0 0 0 0 0 -10 -10 -10 -10 -10 -10 -10 -10 -10 -20 CHANNEL -20 -20 -20 -20 -20 -20 -20 -20 -30 ENTER -40 -30 -40 -30 -40 -30 -40 -30 -40 -30 -40 -30 -40 -30 -40 -30 -40 -60 - - - - - - - - - ANALOG IN ADAT IN EFF RTN 1 9 17 2 10 18 3 11 19 4 12 20 5 13 6 14 7 15 8 16 MASTER CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. "WARNING" "TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. " SAFETY INSTRUCTIONS 1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated. [. . . ] For more information on the Smoothing function, see "Smoothing Function" on page 120. Pre-fader/Post-fader AUX Sends You can configure each AUX Send as pre-fader or post-fader by adjusting parameters on the CURRENT SCENE STATUS function page. Pre-fader signals do not pass through the channel faders and are therefore unaffected by channel fader settings. Post-fader signals pass through the channel faders and are affected by channel fader settings. Follow these steps to configure each AUX Send as pre-fader or post-fader. 1. Press the [CURRENT SCENE STATUS] key. The VM200 displays the CURRENT SCENE STATUS function page. pre-fader/post-fader AUX Sends VM200 User's Guide 117 Outputs 2. 3. Use the Freq and Q rotary controls for channels 1­4 to select PRE or POST for AUX1, AUX2, AUX3, and AUX4. When you change the setting, the selected value flashes. Press the [EXIT] key to display the CHANNEL EDIT function page. Muting AUX Sends You can mute the AUX Send Masters by turning off the [ON] key for the Master channel. Since the Master [ON] key can also mute the Stereo Buss and Effects Send master outputs, depending on the Fader Mode, you need to press the [AUX1], [AUX2], [AUX3], or [AUX4] key to select an AUX Send before you can mute it. 1. 2. Press the [AUX1], [AUX2], [AUX3], or [AUX4] key to select an AUX Send. Use the MASTER [ON] button to turn the AUX Send on and off. When AUX Sends are configured as stereo pairs, their [ON] buttons are linked (see "Pairing Channels" on page 68). See "[ON] Keys" on page 34 for more information. SOLO ON Master ON key 118 VM200 UserÕs Guide Pairing AUX Sends Pairing AUX Sends You can pair AUX Sends 1 and 2 and AUX Sends 3 and 4 for stereo signal processing. When paired, the Master Faders, [ON] keys, and monitors of each AUX Send are set the same and linked for simultaneous control. Follow these steps to pair AUX Sends: 1. Press the [CURRENT SCENE STATUS] key. The VM200 displays the CURRENT SCENE STATUS function page. AUX PAIR parameters 2. 3. Use the Freq and Q rotary controls for channels 7/8 to turn the A1&A2 and A3&4 parameters On or Off. The default setting is "off. " If you change the parameter setting, the indicator flashes. Press the [EXIT] key to return to Channel Edit mode. Note: If the ADD. AUX parameter is on, the REC BUSS is disabled. For more information, see "Enabling AUX Sends 3 & 4 (ADD. AUX Parameter)" on page 115. Note: When AUX1 and 2 are paired, the AUX1 signal is sent to the left channel and AUX2 signal is sent to the right. Similarly, when AUX3 and 4 are paired, the AUX3 signal is sent to the left channel and the AUX4 signal is sent to the right channel. Note: If the Smoothing function is set to Level 2 (default), the AUX pair setting will affect the EFF pair setting. For more information on the Smoothing function, see "Smoothing Function" on page 120. VM200 UserÕs Guide 119 Outputs Smoothing Function Depending on the sound you are mixing, you may hear a slight stepping noise when you slide the faders. To resolve this problem, the VM200 features a Smoothing function that reduces CPU load to achieve smoother fader adjustment. When the Smoothing function is set to Level 2, AUX1 and EFF1 are linked and AUX2 and EFF2 are linked. [. . . ] <Transmission> Bulk Dump is transmitted on the channel specified by [TX CH] when you operate the key in the [BULK DUMP] page. In response to Bulk Dump Request, Bulk Dump is sent on the channel specified by [RX CH]. 4-1. Bulk Dump Request << Setup Bulk Dump Request >> f0 51 <DevId> 2B 'V' 'M' '2' '0' '0' 'A' 01 <Item> f7 <Item> 01:System, 02:Midi, 03:Locate, 127:All Setup << Scene Memory Bulk Dump Request >> f0 51 <DevId> 2B 'V' 'M' '2' '0' '0' 'A' 02 <MemNo> f7 <MemNo> 0: Edit Buffer, 1 ­ 100: UserMemory, 127: All User Memory << Eff Library Bulk Dump Request >> f0 51 <DevId> 2B 'V' 'M' '2' '0' '0' 'A' 03 <LibNo> f7 <LibNo> 50 ­ 99: User Library, 127: All User Library << Eq Library Bulk Dump Request >> f0 51 <DevId> 2B 'V' 'M' '2' '0' '0' 'A' 04 <LibNo> f7 <LibNo> 50 ­ 99: User Library, 127: All User Library << PGM Table Bulk Dump Request >> f0 51 <DevId> 2B 'V' 'M' '2' '0' '0' 'A' 05 00 f7 << CTL Table Bulk Dump Request >> f0 51 <DevId> 2B 'V' 'M' '2' '0' '0' 'A' 06 00 f7 4-2. BULK DUMP OUT FORMAT << Setup Bulk Dump Format >> f0 51 <DevId> 3B <Byte Count L> <Byte Count H> 'V' 'M' '2' '0' '0' 'A' 01 <Item> <Data> --- <Data> <Check Sum> f7 << Scene Memory Bulk Dump Format >> f0 51 <DevId> 3B <Byte Count L> <Byte Count H> 'V' 'M' '2' '0' '0' 'A' 02 <MemNo>> <Data> --- <Data> <Check Sum> f7 <MemNo> 0: Edit Buffer, 1 ­ 100: UserMemory << Eff Library Bulk Dump Format >> f0 51 <DevId> 3B <Byte Count L> <Byte Count H> 'V' 'M' '2' '0' '0' 'A' 03 <LibNo>> <Data> --- <Data> <Check Sum> f7 <LibNo> 50 ­ 99: User Library << Eq Library Bulk Dump Format >> f0 51 <DevId> 3B <Byte Count L> <Byte Count H> 'V' 'M' '2' '0' '0' 'A' 04 <LibNo>> <Data> --- <Data> <Check Sum> f7 <LibNo> 50 ­ 99: User Library << PGM Table Bulk Dump Format >> f0 51 <DevId> 3B <Byte Count L> <Byte Count H> 'V' 'M' '2' '0' '0' 'A' 05 00 <Data> --- <Data> <Check Sum> f7 << CTL Table Bulk Dump Format >> f0 51 <DevId> 3B <Byte Count L> <Byte Count H> 'V' 'M' '2' '0' '0' 'A' 06 00 <Data> --- <Data> <Check Sum> f7 * "Byte Count" is the number of bytes counted from the byte following <Byte Count> up to the byte before <Check Sum>. * "Check Sum" covers after <Byte Count> before <Check Sum>, with all EOR being removed. VM200 User's Guide 223 5. MIDI Device Inquiry Message The VM200 transmits Identity Reply when it receives Identity Request, if the Setup: System EX. [. . . ]