User manual FRIGIDAIRE FAK085R7V

[. . . ] USE & CARE MANUAL NOTE: This USE & CARE MANUAL provides specific operating instructions for your model. Use the room air conditioner only as instructed in this USE & CARE MANUAL. These instructions are not meant to cover every possible condition and situation that may occur. Common sense and caution must be practiced when installing, operating, and maintaining any appliance. Contents 2 3 3 3 4 5-9 10 10 11 Warranty Product Registration Packaging Normal Sounds Important Safety Instructions Air Conditioner Features Care and Cleaning Energy Saving Ideas Avoid Service Checklist READ AND SAVE THESE INSTRUCTIONS SLIDER CASEMENT ELECTRONIC CONTROL AIR CONDITIONER P/N 66129901143 ROOM AIR CONDITIONER WARRANTY Your product is protected by this warranty Your appliance is warranted by Electrolux. [. . . ] To test your power supply cord do the following: 1. The power supply cord will have TWO buttons on the plug head. You will notice a click as the RESET button pops out. Again you will notice a click as the button engages. The power supply cord is now supplying electricity to the unit. (On some products this is also indicated by a light on the plug head). NOTES: · Do not use this device to turn the unit on or off. · Always make sure the RESET button is pushed in for correct operation. · The power supply cord must be replaced if it fails to reset when either the TEST button is pushed, or it cannot be reset. A new one can be obtained from the product manufacturer. · If power supply cord is damaged, it CANNOT be repaired. It MUST be replaced by one obtained from the product manufacturer. NOTE: Some plugs have buttons on the top. 4 Air Conditioner Features ELECTRONIC CONTROL OPERATING INSTRUCTIONS Before you begin, thoroughly familiarize yourself with the control panel and remote as shown below and all its functions, then follow the symbol for the functions you desire. The unit can be controlled by the touch pad alone or with the remote. SETS MODE ADJUSTS TEMPERATURE OR TIME DISPLAYS TEMPERATURE/TIME EXHAUST SELECTOR SETS MODE CHECK FILTER RESET BUTTON ACTIVATES TIMER TURNS UNIT ON OR OFF SETS FAN SPEEDS TOUCH PAD NOTE: The following instructions represent the Touch Pad, the same instructions can be used for the Remote Control. TO TURN UNIT ON: YOU WILL SEE: DO THIS: PRESS ON/OFF BUTTON 5 Air Conditioner Features (continued) TO CHANGE TEMPERATURE SETTING: YOU WILL SEE: DO THIS: PRESS TO RAISE PRESS TO LOWER Note: Tap or hold either up( ) or down( ) botton until the desired temperature is seen on the display. This temperature will be automatically maintained anywhere between 60 (16 ) and 90 (32 ). If you want the display to read the actual room temperature. See "To Operate on on Fan Only" section on Page 6. TO ADJUST FAN SPEEDS: YOU WILL SEE: DO THIS: PRESS TO SELECT: Low, Med, or High The chosen fan speed LED will light up. TO USE AUTO FAN FEATURE: YOU WILL SEE: LIGHT On DO THIS: PRESS TO SELECT: AUTO Note: Fan speed starts at high and adjusts to a slower speed as the room temperature dictates. For example, if the room doesn't get too warm it will stay at the slowest speed. If the room temperature rises quickly, such as a door being opened, it will automatically go to the highest speed. The fan speeds will redjust back to the slowest speed as the room returns to the original set temperature. Press the Fan Speed button to adjust the fan speed manually. 6 Air Conditioner Features (continued) TO OPERATE FAN ONLY: YOU WILL SEE: LIGHT On DO THIS: PRESS MODE BUTTON CHOOSE FAN ONLY Note: Use this function only when cooling is not desired, such as for room air circulation or to exhaust stale air (Remember to open the vent during this function, but keep it closed during cooling for maximum cooling efficiency). You can choose any fan speed you prefer. [. . . ] This list includes common occurrences that are not the result of defective workman-ship or materials in this appliance. SOLUTION Wall plug disconnected. House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker. Turn Control ON and set to desired setting. Air from unit does not feel cold enough. Room temperature below 60°F (16°C). [. . . ]