User manual FRIGIDAIRE FGMO205KF DATASHEET

[. . . ] · Minimum 20" deep oven cutout dimension is critical for proper installation for oven and faceplate to fit flush against cabinet front. · Consult local building code, in the event that cutout opening may be required to be enclosed with sides, ceiling and rear partition. · Full oven base of solid plywood or similar material required, capable of supporting 100 Lbs. · Can NOT be installed above any gas wall oven. · Built-In Microwave is approved to be used in combination with any Frigidaire® Electric Single Wall Oven and/or Warmer Drawer. [. . . ] · Full oven base of solid plywood or similar material required, capable of supporting 200 Lbs. · To adapt oven to fit cutout height greater than 28-1/8", add one 2"-wide wood shim of appropriate height to each side of opening under oven side rails. Lifting oven will hide larger cutout opening at top and oven's 1"-high bottom trim will hide shims at bottom. (Standard 1"- High Bottom Trim included. ) · To adapt oven to fit cutout height greater than 28-5/8", optional 3"- High Bottom Trim available. Note: For planning purposes only. Refer to Product Installation Guide on the web at frigidaire. com for detailed instructions. 30" Trim Kit which includes Bottom Duct Assembly ­ shipped in separate box, ordered by individual part number. · Voltage Rating ­ 120V/60 Hz/15 or 20 Amps · Connected Load (kW Rating) @ 120 Volts = 1. 7 kW (For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation. ) · Amps @ 120 Volts = 14. 3 Amps · Full oven base of solid plywood or similar material required, capable of supporting 100 Lbs. · Minimum 2-7/8" clearance required from bottom of Built-In Microwave cutout to top edge of Wall Oven's faceplate, leaving a 2" visible gap between both product faceplates. USA · 10200 David Taylor Drive · Charlotte, NC 28262 · 1-800-FRIGIDAIRE · frigidaire. com CANADA · 5855 Terry Fox Way · Mississauga, ON L5V 3E4 · 1-800-265-8352 · frigidaire. ca MOSS24_EW 30INST FR 06/11 © 2011 Electrolux Home Products, Inc. Specifications subject to change. Printed in the U. S. A. 30"Combination Installation Built-In Microwave/Single Wall Oven/Warmer Drawer 30" Combination Installation Specifications · Always consult local and national electric codes. 30" Electric Single Wall Oven Specifications · Single phase 3- or 4-wire cable, 120/240 or 120/208 Volt, 60 Hertz (Refer to product-specific electrical specifications on this page. ) · Minimum 23-5/8" deep cutout dimension is critical for proper combination installation, to ensure that each built-in product's faceplate will fit flush against cabinet front. · Bases must be level and cabinet front must be square. · Minimum 4-1/2" required distance from bottom of Warmer Drawer cutout to floor. · Respect critical dimensions as noted for proper installation of built-In products. · Minimum 21" clearance needed for Wall Oven door depth when open. AC only electrical supply with ground required on separate circuit fused on both sides of line. · For detailed electrical requirements, refer to model-specific product page and installation guide on web. · To support Wall Oven when using in combination with Warmer Drawer, two 3"-wide x 3/4"-thick planks must be installed as a base, capable of supporting 200 Lbs. Do NOT use full base, since planks are necessary to allow for proper air displacement. 30" Warmer Drawer Specifications · Voltage Rating ­ 120V/450W/60 Hz/15 Amps · Connected Load (kW Rating) @ 120 Volts = 0. 5 kW 30" Built-In Microwave Specifications · For built-in installation, microwave MUST be installed with optional 30" Trim Kit which includes Bottom Duct Assembly ­ shipped in separate box, ordered by individual part number. · Voltage Rating ­ 120V/60 Hz/15 or 20 Amps · Connected Load (kW Rating) @ 120 Volts = 1. 7 kW (For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation. ) · Amps @ 120 Volts = 14. 3 Amps · Full oven base of solid plywood or similar material required, capable of supporting 100 Lbs. · Minimum 2-7/8" clearance required from bottom of Built-In Microwave cutout to top edge of Wall Oven's faceplate, leaving a 2" visible gap between both product faceplates. (For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. [. . . ] · To support Wall Oven when using in combination with Warmer Drawer, two 3"-wide x 3/4"-thick planks must be installed as a base, capable of supporting 200 Lbs. Do NOT use full base, since planks are necessary to allow for proper air displacement. 27" Warmer Drawer Specifications · Voltage Rating ­ 120V/450W/60 Hz/15 Amps · Connected Load (kW Rating) @ 120 Volts = 0. 5 kW 27" Built-In Microwave Specifications · For built-in installation, microwave MUST be installed with optional 27" Trim Kit which includes Bottom Duct Assembly ­ shipped in separate box, ordered by individual part number. · Voltage Rating ­ 120V/60 Hz/15 or 20 Amps · Connected Load (kW Rating) @ 120 Volts = 1. 7 kW (For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation. ) · Amps @ 120 Volts = 14. 3 Amps · Full oven base of solid plywood or similar material required, capable of supporting 100 Lbs. [. . . ]