User manual FRIGIDAIRE FRA053PU1

[. . . ] All about the Use &Care of your Portable Air Conditioner TA B L E O F C O N T E N T S Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Product Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Normal Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Unit Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 17 Window stool Window slider kit Foam seal Fig. 19 2009 Electrolux Home Products, Inc. Fig. 18 7 Air Conditioner Features Air Conditioner Features CONTROL PANEL DISPLAYS TEMPERATURE/TIME TURNS UNIT ON OR OFF SWING BUTTON SLEEP MODE SETS MODE ADJUSTS TEMPERATURE OR TIME SETS FAN SPEED CHECK FILTER RESET BUTTON ACTIVATES TIMER Fig. 21 REMOTE CONTROL MODE INDICATION FAN SPEED SELECTION TEMPERATURE/TIMER CONTROL BUTTONS MODE SELECTOR SLEEP BUTTON FAN SPEED SELECTOR TIMER BUTTONS SWING BUTTON ON/OFF BUTTON RESET + LOCK PIN BUTTONS Fig. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickelcadmium) batteries. In this mode there is no need to use the exhaust hose or drainage hose. However, if you require stale or smokey air to be removed from the room, hook up the duct accessories as described in the "EXHAUSTING HOT AIR" section. Press the MODE button until the "Fan" indicator lights. Press the FAN button to choose the desired fan speed. The fan will run at the selected speed and the display will show the room temperature. You can set both delay stop and delay start while unit is in ON position or OFF position. When unit is in ON position, first press TIMER button to go to delay stop setting, then "timer off" light will illuminate, tap or hold the UP arrow ( ) or the DOWN arrow ( ) to change delay stop timer at 0. 5 hour increments up to 10 hours, then at 1 hour increments up to 24 hours. Then press the TIMER button to confirm the setting (the control will confirm the setting automatically after 5 seconds) and go to delay start setting. Use the same way as above to set the delay start timing. If you don't need to set delay start, press the TIMER button again to exit. After 5 seconds, the control will automatically change the display back to previous temperature display. If you want to check remain timing, press the TIMER button. The delay start operation automatically selects mode, temperature and fan speed the same as last operation you set. When unit is in OFF position, press TIMER button will first go to delay start setting, then "timer on" light will illuminate, set the delay start and delay stop timing the same way as above. To cancel the timer setting, simply tap ( ) or ( ) button to change the timing to 0. 0. In this mode the selected temperature will increase by 2 °F 30 minutes after the mode is selected. The temperature will then increase by another 2 °F after an additional 30 minutes. [. . . ] Service calls to correct the installation of your appliance or to instruct you how to use your appliance. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc. , which are not a part of the appliance when it is shipped from the factory. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs, handles, or other cosmetic parts. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip charges, or mileage expense for service calls to remote areas, including the state of Alaska. [. . . ]