User manual FRIGIDAIRE FRA08PZU1

[. . . ] All about the Use &Care of your Room Air Conditioner TA B L E O F C O N T E N T S Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Product Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Normal Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] First, Press TIMER button, then adjust timer setting, tap or hold the UP arrow ( ) or the DOWN arrow ( ) to change delay timer at 0. 5 hour increments, up to 10 hours, then at 1 hour increments up to 24 hours. The control will count down the time remaining until start (8, 7. 5, 7, etc. ). The Delay Start Operation automatically selects cooling with maximum Fan speed (if Cool, Energy Saver, or Fan Only was the last mode selected) . The temperature maintained will be the same as previously set. lt will periodically send this signal until the feature is deactivated by pressing the remote sensing Stop button. lf the unit does not receive the remote sensing signal during any 3 minute interval, the unit will beep to indicate the remote sensing mode has ended. The display on the remote control indicates the temperature at the remote ONLY. NOTE: The Remote Sensing function is terminated either by using the Remote Sensing Stop button or the main ON/OFF button on the unit. HEATING FEATURE(on some models): YOU WILL SEE: DO THIS: PRESS MODE BUTTON, CHOOSE HEAT Note: This feature can be used with any combination of FAN Speeds (Low speed only on 115V models), Timer, or Sleep Modes. When in the "Heat" mode, the fan will run continuously while heat is needed. The temperature will automatically be maintained anywhere between 55 °F(13 °C) and 80 °F(27 °C) (The upper limit of temperature could reach 86°F(30 °C) on some of the 115V models. ). When the room set temperature is satisfied, the fan will cycle off and on to circulate and sample the room air. FAULT CODES: If the display reads "HS", "AS", "ES", "CS" or "OS", a sensor has failed. Contact your Authorized Frigidaire Service Center. 2009 Electrolux Home Products, Inc. All rights reserved. 9 Operating Instructions Operating Instructions (continued) TO CHANGE TEMPERATURE DISPLAY: YOU WILL SEE: DO THIS: PRESS AND HOLD THE UP/DOWN BUTTONS TOGETHER FOR 3 SECONDS Note: The control is capable of displaying temperature in degrees Fahrenheit or degrees Celsius. TO TURN UNIT OFF: YOU WILL SEE: DO THIS: PRESS ON/OFF BUTTON ADDITIONAL THINGS YOU SHOULD KNOW Now that you have mastered the operating procedure, here are more features in your control that you should become familiar with. The "Cool" circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly. This prevents overheating of the compressor and possible circuit breaker tripping. The fan will continue to run during this time. There is a 2-Second delay for the compressor shutting down when selecting FAN ONLY/HEAT. This is to cover the possibility of having to roll through to select another mode. The control will maintain the set temperature within 2 degrees Fahrenheit, between 60F and 90F degrees in cool mode, 55F and 80F degrees in heat mode(the upper limit of temperature could reach 86F degrees on some of the 115V models). After a power outage, the unit will memorize the last setting and return the unit to the same setting once power is restored. Fresh Air Vent Control (on some models) The Fresh Air Vent allows the air conditioner to: 1. Recirculate inside air - Vent Closed (see Fig. Draw fresh air into the room - Fresh Air (see Fig. Exchange air from the room - Vent Open (see Fig. [. . . ] Service calls to correct the installation of your appliance or to instruct you how to use your appliance. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc. , which are not a part of the appliance when it is shipped from the factory. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs, handles, or other cosmetic parts. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip charges, or mileage expense for service calls to remote areas, including the state of Alaska. [. . . ]