User manual FRIGIDAIRE GLMV169 Installation Instruction

[. . . ] The mounting surfaces must be capable of supporting weight of 110 pounds--the oven and contents--AND the weight of all items which would normally be stored in the top cabinet above the unit. The unit should be attached to a minimum of one 2" x 4" wall stud or two 2" x 3" wall studs. To find the location of the studs, one of the following methods may be used: 12" 30" 15. 5" Backsplash At least 2" 30" or more from cooking surface A. Use a stud finder, a magnetic device which locates the nails in the stud. [. . . ] Lift carton off oven and remove all packing materials, Installation Instructions, Wall Template, Top Template, Charcoal Filter, Turntable and Turntable Support; however, DO NOT REMOVE THE WAVEGUIDE COVER, which is located on the ceiling in the oven cavity. SAVE THE CARTON AS IT MAY MAKE INSTALLATION EASIER. Check the oven for any damage, such as misaligned or bent door, damaged door seals and sealing surfaces, broken or loose door hinges and latches and dents inside the cavity or on the door. If there is any damage, do not operate the oven and contact your dealer or ELECTROLUX AUTHORIZED SERVICER. Remove and save Screws (A) as shown in Figure 5. Pull the louver away from the unit and set aside. 6 INSTALLATION HARDWARE The INSTALLATION HARDWARE (items 1 - 8) packed with the oven should contain the following: Item 1 2 3 4 5 6 7 8 9 Name Wood Screw 5 X 30 mm Toggle Bolt 3/16 inch Top Cabinet Screw 5 X 60 mm Flat Washer 30 mm diameter Power Cord Hanger Grommet Tapping Screw 4 x 12 mm Exhaust Damper Assembly Charcoal Filter Quantity 6 4 2 2 1 1 4 1 1 5. Loosen the two Mounting Screws (D) which secure the Mounting Plate to the rear side of the oven. See Figure 6. (A) Mounting Plate (A) (A) (A) Control Panel Side Figure 5 Mounting Plate (D) (D) Figure 4 Parts shown not to common scale. Figure 6 3 Installation Instructions 8 VENTILATION SYSTEM (PREPARING OVEN FOR INSTALLATION) This Microwave Oven/Hood is designed for adaptation to three types of hood ventilation systems. Select the type required for your installation. Recirculating requires the use of the Charcoal Filter, which has been installed in the oven. Horizontal Exhaust -- outside ventilation. Vertical Exhaust -- outside ventilation. Replace the Fan Cover Bracket by sliding it into the slits in the same direction as the arrow on the Fan Cover Bracket. Make sure the fan blades are visible through the rear openings in the oven before proceeding. Attach Fan Cover Bracket to unit with 3 screws, which were removed in Step 1 above. The Hood Fan Unit is now rotated for horizontal exhaust operation. Attach the Exhaust Damper Assembly to the back of the Mounting Plate by sliding it into the slits in the same direction as the arrow. Use Tapping Screw 4 X 12 from the INSTALLATION HARDWARE and tighten into place. (A) RECIRCULATING: Non-Vented, Ductless Operation 1. The unit is shipped assembled for recirculating. The Exhaust Damper Assembly is not required for recirculating exhaust. Charcoal Filter, included with the unit, is required for recirculating exhaust. Attach the Charcoal Filter to the upper side of the oven by sliding into the tabs. [. . . ] Withdraw Hood Fan Unit carefully and slip wires out of Wire Box. CAUTION: Do not pull or stretch hood fan wiring. Rotate the Hood Fan Unit 90° so that the fan blade openings are facing upward. Be careful not to pinch the lead wire between the inner bracket and the Hood Fan Unit. [. . . ]