User manual FUJITSU SIEMENS D1381 TECHNICAL MANUAL

[. . . ] Denna handbok är tryckt på recyclingpapper. Dit handboek werd op recycling-papier gedrukt. Herausgegeben von/Published by Fujitsu Siemens Computers GmbH Bestell-Nr. /Order No. : A26361-D1381-Z120-1-7419 Printed in the Federal Republic of Germany AG 0402 04/02 A26361-D1381-Z120-1-7419 German English Systembaugruppe D1381 System Board D1381 Technisches Handbuch Technical Manual Ausgabe April 2002 April 2002 edition Pentium and Celeron are registered trademarks of Intel Corporation, USA. Microsoft, MS, MS-DOS and Windows are registered trademarks of Microsoft Corporation. [. . . ] Please observe the safety information provided in the "Important notes" chapter in the device's operating manual. Incorrect replacement of the lithium battery may lead to a risk of explosion. It is therefore essential to observe the instructions in the "Add-on modules" - "Replacing the lithium battery" section. A26361-D1381-Z120-1-7419 English - 1 Important notes The shipped version of this board complies with the requirements of the EEC directive 89/336/EEC "Electromagnetic compatibility". Compliance was tested in a typical PC configuration. When installing the board, refer to the specific installation information in the Operating Manual or Technical Manual for the receiving device. Connecting cables for peripherals must be adequately shielded to avoid interference. ! i Components can become very hot during operation. Ensure you do not touch components when making extensions to the system board. The warranty is invalidated if the device is damaged during the installation or replacement of system expansions. Information on which system expansions you can use is available from your sales outlet or the customer service centre. Information about boards To prevent damage to the system board or the components and conductors on it, please take great care when you insert or remove boards. Take great care to ensure that extension boards are slotted in straight, without damaging components or conductors on the system board, or any other components, for example EMI spring contacts. Be especially careful with the locking mechanisms (catches, centring pins etc. ) when you replace the system board or components on it, for example memory modules or processors. Never use sharp objects (screwdrivers) for leverage. Boards with electrostatic sensitive devices (ESD) are identifiable by the label shown. When you handle boards fitted with ESDs, you must, under all circumstances, observe the following points: · · · · · You must always discharge static build up (e. g. by touching a grounded object) before working. The equipment and tools you use must be free of static charges. Remove the power plug from the mains supply before inserting or removing boards containing ESDs. Always hold boards with ESDs by their edges. Never touch pins or conductors on boards fitted with ESDs. 2 - English A26361-D1381-Z120-1-7419 Features Features The components and connectors marked are not necessarily present on the system board. · System board in µATX format Intel processor Pentium 4 from 1. 4 GHz with 400 /533 MHz Front Side Bus. Pentium 4 processors support MMX technology and Intel Streaming SIMD Extensions. The size and frequency of first-level cache and second-level cache are dependent upon the processor used. · · · · · · · Intel chipset 845G Intel 82559ET LAN controller (10/100 Mbit/s) with RJ45 interface WOL with Magic Packetä is supported, as is booting from LAN with InCom LAN BootP or Intel PXE. VGA: 24 bit and 350 MHz RAMDAC; Dynamic Video Memory (DVM) Analogue Devices AD1981A (AC'97) Audio Codec internal: Stereo CD-In, Audio front panel external: Mono Micro-In, Stereo Line-In, Stereo Line-Out 2 DIMM slots for 128 MB up to 2 GB main memory (DDR-DIMM memory modules meet the PC2100 specification) without ECC Flash BIOS Power-on functions: Wake on RTC Wake on LAN Wake on PCI Cards Wake on USB COM1 wake up support (standby) APM and ACPI (requires an operating system that supports ACPI) Switching on/off, standby mode, suspend mode via on/off switch Switching on/off via software Processor serial number Cover monitoring: cover monitoring reports when the cover has been opened without authorisation. [. . . ] Carefully remove the memory module from the compartment (2). A26361-D1381-Z120-1-7419 English - 11 Add-on modules Replacing the lithium battery ! Incorrect replacement of the lithium battery may lead to a risk of explosion. The lithium battery must be replaced with an identical battery or a battery type recommended by the manufacturer (CR2032). Do not throw lithium batteries into the household waste. They must be disposed of in accordance with local regulations concerning special waste. [. . . ]