User manual FUJITSU SIEMENS SCENIC D (I815E)

[. . . ] Microsoft, MS, MS-DOS und Windows sind eingetragene Warenzeichen der Microsoft Corporation. PS/2 und OS/2 Warp sind eingetragene Warenzeichen von International Business Machines, Inc. Alle weiteren genannten Warenzeichen sind Warenzeichen oder eingetragene Warenzeichen der jeweiligen Inhaber und werden als geschützt anerkannt. Copyright ã Fujitsu Siemens Computers GmbH 2001 Alle Rechte vorbehalten, insbesondere (auch auszugsweise) die der Übersetzung, des Nachdrucks, der Wiedergabe durch Kopieren oder ähnliche Verfahren. [. . . ] 12 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 A26361-D1321-Z120-1-7419 Introduction i Depending on the configuration chosen, some of the hardware components described may not be available on your system board. You will find further information in the "BIOS Setup" description. Further information about drivers is provided in the readme files on the hard disk, on the supplied drivers diskettes, on the "Drivers & Utilities" or on the "ServerStart" CD. Notational conventions The meanings of the symbols and fonts used in this manual are as follows: ! i Ê Ë Ú Pay particular attention to text marked with this symbol. Failure to observe this warning endangers your life, destroys the device, or may lead to loss of data. Supplementary information, remarks, and tips follow this symbol. Text which follows this symbol describes activities that must be performed in the order shown. This symbol indicates that you must enter a blank space (press the Space Bar) at this point. This symbol indicates that you must press the Enter key. Text in this typeface indicates screen outputs. Text in this bold typeface indicates the entries you make via the keyboard. Text in italics indicates commands or menu items. "Quotation marks" indicate names of chapters or terms. Important notes Store this manual close to the device. If you pass the device on to third parties, you should pass this manual on with it. The size and frequency of first-level cache and second-level cache are dependent upon the processor used. Intel chipset 845 Intel 82559ET LAN controller (10/100 Mbit/s) with RJ45 interface WOL with Magic Packetä is supported, as is booting from LAN with Bootix LAN BootP or Intel PXE. Analogue Devices AD1885 (AC'97) Audio Codec internal: Stereo CD-In, Stereo AUX-In external: Mono Micro-In, Stereo Line-In, Game/Midi port Stereo Line-out / headphones 3 DIMM slots for 32 MB to 3 GB main memory (SDRAM memory modules meet the PC133 specification) with ECC Flash BIOS Power-on functions: - - - - - Wake on RTC Wake on LAN Wake on PCI Cards Wake on USB COM1 wake up support (standby) APM and ACPI (requires an operating system that supports ACPI) Switching on/off, standby mode, suspend mode via on/off switch Switching on/off via software Processor serial number Cover monitoring: cover monitoring reports when the cover has been opened without authorisation. System, Setup and Keyboard password parallel and serial ports can be deactivated Floppy disk write-protection via BIOS Setup Boot hard disk virus warning function Flash BIOS and EEPROMs (on the memory modules) virus protection function. · · · · Energy saving functions: - - - · Security functions: - - - - - - - · 3 PCI slots PCI slots support 3. 3 V main and auxiliary voltages. A26361-D1321-Z120-1-7419 English - 3 Features · · 1 AGP slot The AGP slot supports 1x, 2x and 4x AGP mode. Only AGP boards with 1. 5 V are supported. IDE hard disk controller connected to PCI bus for up to four IDE drives (e. g. IDE hard disk drives, ATAPI CD-ROM drives) The IDE hard disk controller are ATA33/66/100, ultra DMA capable and support PIO modes 04. Floppy disk drive controller (possible formats: 720 KB, 1. 44 MB, 2. 88 MB) The system board supports booting from a 120 MB IDE floppy disk drive. Real-time clock/calendar with integrated battery backup 1 internal WOL interface 2 internal USB ports (C / D) 1 external parallel port (ECP- and EPP-compatible) 2 external serial ports (16C550 compatible with FIFO) 2 external PS/2 ports for keyboard and mouse 2 external USB ports (A / B) · · · · · · · · · External ports 13 4 5 6 8 2 7 9a 9b9c 1= 2= 3= 4= 5= 6= 7= PS/2 mouse port PS/2 keyboard port Serial port 1 Parallel port Serial port 2 LAN connector USB ports A and B 8 = Game/Midi port 9a = Audio Line-Out Headphones 9b = Audio Line-In 9c = Audio Micro-In The components and connectors marked are not necessarily present on the system board. 4 - English A26361-D1321-Z120-1-7419 Features Internal ports and connectors 1 23 4 5 6 7 8 DIMM 3 DIMM 2 DIMM 1 14 AGP 9 10 PCI 1 13 1= 2= 3= 4= 5= 6= 7= 8= Power supply ATX Floppy Disk Drive IDE drives 3 and 4 (secondary) Connector for control panel and loudspeaker IDE drives 1 and 2 (primary) Voltage indicator LED Fan 2 Cover monitoring 12 PCI 2 11 9 = USB ports C / D * 10 = Wake On LAN 11 = CD audio input 12 = AUX audio input 13 = Power supply +12 V 14 = Fan 1 (e. g. for the processor) The components and connectors marked are not necessarily present on the system board. PCI 3 A26361-D1321-Z120-1-7419 English - 5 Features Hard disk connection An ultra ATA/66 or ultra ATA/100 hard disk must be connected with a cable especially designed for the ultra ATA/66or ultra ATA/100 mode. Ê Connect the end of the cable marked with blue to the system board. LAN connector This system board has an optional Intel 82550ET LAN controller which supports transfer speeds of 10 Mbit/s and 100 Mbit/s. The LAN controller is equipped with a 3 KB transmission and receiving buffer (FIFO) and supports WOL function through Magic Packetä. [. . . ] Carefully remove the memory module from the compartment (2). 10 - English A26361-D1321-Z120-1-7419 Add-on modules Installing network board with WOL Ê Ê Install the network board as described in the operating manual for your unit. Push the WOL cable onto the WOL plug connector of the system board. To use the WOL functionality of a network board the power supply must provide a 5 V auxiliary voltage of at least 1 A. If the system board was not already incorporated in a device when you bought it you must check whether your power supply can provide the auxiliary voltage. [. . . ]