User manual FUJITSU SIEMENS SCENIC E300 (I865GV)

[. . . ] Please contact: · your sales partner · your sales outlet You will find further information in the manuals "Safety" and "Ergonomics". BIOS update) on our mainboards can be found on the Internet under: http://www. fujitsu-siemens. com/mainboards Dieses Handbuch wurde auf Recycling-Papier gedruckt. This manual has been printed on recycled paper. Ce manuel est imprimé sur du papier recyclé. [. . . ] System and BIOS Setup password must be entered when the device is switched on. Recovering System BIOS - switch 2 Switch 2 enables recovery of the old system BIOS after an attempt to update has failed. To restore the old system BIOS you need a Flash BIOS Diskette (please call our customer service centre). On Off The System BIOS executes from floppy drive A: and the inserted "Flash-BIOSDiskette" restores the System BIOS on the mainboard. Normal operation (default setting). Reserved - switch 3 and switch 4 Switch 3 and 4 are reserved. A26361-D1451-Z120-4-6319 English - 13 Installing and removing processors Add-on modules / Upgrading ! Exit energy-saving mode, switch off the system and remove the power plug from the mains outlet, before carrying out any of the procedures described in this chapter!Even when you have switched off the device, parts (e. g. memory modules, AGP and PCI extension boards) are still supplied with power. Installing and removing processors Technical data Intel Pentium 4 with 400 or 533 MHz system bus in the mPGA478 design. Celeron with 400 MHz System Bus in the mPGA478 design. A current list of the processors supported by this mainboard is available on the Internet at: www. fujitsu-siemens. com/mainboards. www. fujitsu-siemens. com/mainboards. Installing the processor with heat sink and fan Ê Remove the fan that there may be and the heat sink. 3 2 4 5 1 A Ê Ê Pull the lever in the direction of the arrow (1) and lift it as far as it will go (2). Insert the new processor in the socket so that the angled corner of the processor matches the coding on the socket (A) with regard to the position (4). Remove the old processor from the socket (3). i The angled corner of the processor can also be at a different location than shown in the illustration. Push the lever back down until it clicks into place (5). 14 - English A26361-D1451-Z120-4-6319 Installing and removing processors Mounting heat sink Be sure to use heat conducting material between the processor and the heat sink. If a heat conducting pad (rubber-like foil) is already applied to the heat sink, then use it. Expansion cards that do not require an interrupt can be installed in any desired slot. A26361-D1451-Z120-4-6319 English - 17 Adding PCI cards Multifunctional expansion cards or expansion cards with integrated PCI-PCI bridge: These expansion cards require up to four PCI interrupts: INT A, INT B, INT C, INT D. How many and which of these interrupts are used is specified in the documentation provided with the card. The assignment of the PCI interrupts to the PCI IRQ Lines is shown in the following table: Onboard controller PCI INT LINE 1 (A) 2 (B) 3 (C) 4 (D) 5 (E) 6 (F) 7 (G) 8 (H) USB 1, 1 1st A 2nd A 3rd A USB 2, 0 A SM Bus A AC97 Audio A Modem A LAN A Graphic A PCI slot 1 A B C D 2 A B C D 3 A B C D - Use the first PCI slots that have a single PCI IRQ Line (no IRQ sharing). If you must use another PCI slot with IRQ sharing, check whether the expansion card properly supports IRQ sharing with the other devices on this PCI IRQ Line. The drivers of all cards and components on this PCI IRQ Line must also support IRQ sharing. Replacing lithium battery In order to permanently save the system information, a lithium battery is installed to provide the CMOS-memory with a current. A corresponding error message notifies the user when the charge is too low or the battery is empty. The lithium battery must then be replaced. ! Incorrect replacement of the lithium battery may lead to a risk of explosion!The lithium battery may be replaced only with an identical battery or with a type recommended by the manufacturer. Do not throw lithium batteries into the household waste. They must be disposed of in accordance with local regulations concerning special waste. Make sure that you insert the battery the right way round. [. . . ] Check whether you have assigned the same device ID twice. xy = Group number x = Number of SEs found on the communication bus y = Number of SEs entered in Number of connected SE k1, k2 . . . = Device ID of the storage extensions found 28 - English A26361-D1451-Z120-4-6319 DOS error messages System battery is dead - Replace and run SETUP Replace the lithium battery on the mainboard and redo the settings in the BIOS Setup. System Cache Error - Cache disabled Switch the device off and on again. [. . . ]