User manual FUJITSU SIEMENS SCENIC EDITION MEDIAMIT D6/M6

[. . . ] This symbol is followed by supplementary information, remarks and tips. ² Texts which follow this symbol describe activities that must be performed in the order shown. ³ ´ This symbol means that you must enter a blank space at this point. This symbol means that you must press the Enter key. Texts in this typeface are screen outputs from the PC. Texts in this bold typeface are the entries you make via the keyboard. Texts in italics indicate commands or menu item. [. . . ] If the ultra-wide SCSI controller is not the last device on the SCSI cable, its terminator must be disabled. LowON/HighON The termination is enabled (default entry). LowOFF/HighOFF The termination is disabled. LowON/HighON Not supported. 22 - English A26361-D981-Z120-9-7419 SCSI Setup Additional Options Additional Options Boot Device Options Boot Target ID The ultra-wide SCSI controller can start the operating system from a drive with any SCSI address (ID). The SCSI ID selected here must correspond to the ID configured on the boot device. 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15 The ultra-wide SCSI controller boots from the drive with the displayed SCSI ID (default entry: 0). Boot LUN Number If your boot device has multiple LUNs (Logical Unit Numbers) and Multiple LUN Support is Enabled, this option allows you to specify which LUN to boot from on your boot device. 0, 1, 2, 3, 4, 5, 6, 7 The ultra-wide SCSI controller boots with the displayed LUN (default entry: 0). SCSI Device Configuration Initiate Sync Negotiation Devices on the SCSI bus (including the SCSI controller) communicate intelligently with each other. Before data is transferred across the bus, the sending (initiating) and receiving (target) devices negotiate and agree on how long each piece of data will be, and how many pieces will be sent at a time - that is, they agree on how fast to talk. If you have operating problems with older SCSI devices, you should disable Initiate Sync Negotiation. You may have to make settings on your SCSI devices (see the SCSI device description). A26361-D981-Z120-9-7419 English - 23 Additional Options SCSI Setup When Sync Negotiation is disabled, the Ultra-Wide SCSI controller will automatically go into synchronous mode if it receives a request from one of your SCSI devices. It can, however, also exchange data with slow SCSI devices. Enabled Disabled The SCSI bus will be reset (default entry). The SCSI bus will not be reset. Host Adapter BIOS ! If the SCSI BIOS is disabled, the system cannot be booted from any of the SCSI devices connected to the SCSI bus. The SCSI BIOS can be disabled if the SCSI devices can only be operated with additionally loaded drivers. This saves 16 Kbytes of system memory as well as time during system startup. If you disable the SCSI BIOS, you can still call the SCSI Setup with the >&WUO@ + >$@ keys during system startup and modify settings. Enabled Disabled The SCSI-BIOS is enabled (default setting). Note that you will have to install additional drivers for your devices if the SCSI BIOS is disabled. i 26 - English A26361-D981-Z120-9-7419 SCSI Setup Support Removable Disks under BIOS as Fixed Disks Additional Options This option allows you to use removable-media drives, such as MO drives, without installing additional drivers. Boot Only All Disks Disabled Only the removable-media drive designated as the boot device is treated as a hard disk (default setting). All removable-media drives supported by the BIOS are treated as hard disk drives. No removable-media drives are treated as hard disk drives. In this situation, software drivers are needed because the drives are not controlled by the BIOS. If a removable-media device is controlled by the SCSI controller BIOS, do not remove the media while the system is switched on. ! Extended BIOS Translation for DOS Drives > 1Gbyte Enabling this option allows drives of up to 8 Gbyte capacity (2 Gbyte/partition) to be supported under MS-DOS 5. 0 or higher. [. . . ] 14 Resource table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 SCSI Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Setting SCSI addresses (IDs). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Connecting SCSI devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]