User manual FUJITSU SIEMENS SCENIC XB (I815)

[. . . ] Herausgegeben von/Published by Fujitsu Siemens Computers GmbH Bestell-Nr. /Order No. : A26361-D1184-Z180-1-7619 Printed in the Federal Republic of Germany AG 0600 06/00 A26361-D1184-Z180-1-7619 System Board D1184 Additional Technical Manual June 2000 edition Intel, Pentium and Celeron are registered trademarks and MMX and OverDrive are trademarks of Intel Corporation, USA. Microsoft, MS, MS-DOS and Windows are registered trademarks of Microsoft Corporation. PS/2 is a registered trademark of International Business Machines, Inc. All other trademarks referenced are trademarks or registered trademarks of their respective owners, whose protected rights are acknowledged. Copyright ã Fujitsu Siemens Computers GmbH 2000 All rights, including rights of translation, reproduction by printing, copying or similar methods, even of parts are reserved. [. . . ] 12 A26361-D1184-Z180-1-7619 Introduction i This system board is available in different configuration levels. Depending on the hardware configuration of your device, it may be that you cannot find several options in your version of the system board, even though they are described. You may find further information e. in the complete Technical Manual for the system board and in the description "BIOS Setup". Further information to drivers is provided on the supplied drivers diskettes or on the "Drivers & Utilities" or "ServerStart" CD. For detailed information please look at chapter "Installing drivers". The latest BIOS version or drivers can be found on the internet under http://www. fujitsusiemens. com/en/service. FCC Class B Compliance Statement This system board has been tested and found to comply with the limits for a "Class B" digital device, pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian Interference-Causing Equipment Regulations. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in strict accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna. Increase the separation between equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Fujitsu Siemens Computers GmbH is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Fujitsu Siemens Computers GmbH. The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user. The use of shielded I/O cables is required when connecting this equipment to any and all optional peripheral or host devices. Failure to do so may violate FCC rules. A26361-D1184-Z180-1-7619 English - 1 Features Features The table shows two assembly versions of this system board as example. Function Processor socket Processor Formfactor Front Side Bus in MHz Chipset Memory sockets ISA slots PCI slots ISA/PCI shared AGP Port AMR Port System monitoring Thermal Management Wake On LAN Chipcard reader Save to Disk (ACPI S4) Save to RAM(ACPI S3) LAN onboard Audio onboard VGA onboard 133 MHz Display Cache Version D1184-A1X PGA 370 Intel Celeron or Pentium III ATX 66/100/133 815 3 DIMM -5 -1 1 x x x x x x x AD1881A i 815 -Version D1184-B1X PGA 370 Intel Celeron or Pentium III ATX 66/100/133 815 3 DIMM -5 -1 1 x x -x x x -AD1881A i 815 -- ! Computer system boards and components contain very delicate IC chips. To protect them against damage caused from electric static, you have to follow some precautions: · · · Unplug your computer when you work inside. Hold components by the edge, don't touch their leads. Use a grounded wrist strap. Place the system board and the components on a grounded antistatic pad whenever you work outside the computer. [. . . ] 168 pin, 3. 3 V, 64 bit, 72 bit (with ECC), SDRAM 2 M, 4 M, 8 M, 16 M and 32 M x 64 bit 2 M, 4 M, 8 M, 16 M and 32 M x 72 bit For one socket 16, 32, 64, 128 or 256 Mbyte SDRAM modules with ECC can be plugged in but ECC is not functioning. Mix of ECC modules with non ECC modules is possible. Support for up to 3 single sided or 2 double sided DIMM modules. Granularity: Troubleshooting Message BIOS update The System BIOS provides optimum support for the processor you have chosen. If the message BIOS update for installed CPU failed appears the microcode required for the processor inserted must still be loaded. [. . . ]