User manual FUJITSU SIEMENS SCENICO P300 (VKM266)

[. . . ] Please contact: our Hotline: Tel. : (01923) 209 109 your sales partner your sales office . . . anything you want to tell us about this manual?Please send us your comments quoting the order number of the manual. Siemens Nixdorf Informationssysteme AG User Documentation Department, BS2000 OS ID4 Otto-Hahn-Ring 6 D-81730 München i Only SCENIC-certified components guarantee the described SCENIC functionality. Introduction Important notes SCENIC PT Preparation for use and operation Settings in BIOS Setup Operating Manual Property and data protection Troubleshooting and tips System expansions Technical data Index June 1996 edition Contents Your training needs? The Siemens Nixdorf Training Centers offer you a wide range of training courses in information technology and on IT products and other subjects - onsite near to your workplace or offsite at one of our training centers. [. . . ] If you attach a serial mouse, you can disable the mouse controller in the BIOS Setup in order to free the IRQ12 for a different application. If the mouse controller is disabled, you will not be able to operate either the supplied mouse nor a mouse connected to the PS/2 mouse port. Only active loudspeakers may be used. The external microphone must be a dynamic microphone or a condenser microphone. Connect the cable of the external loudspeakers to the audio output of the system unit. Connect the cable of the external microphone to the microphone port of the system unit. Connect the audio output of the external audio device (e. mixer, stereo system) to the audio input of the system unit. Connecting devices with serial or parallel ports Connect the data cable to the external device. Connect the data cable of the external device to the appropriate port on the system unit. Connecting a joystick Connect the data cable of the joystick to the Game/Midi port of the system unit. i Most devices that you connect to the serial or parallel port require special drivers. MS-Windows already includes many drivers but if the driver you need is not on the hard disk please install it from the floppy disk supplied with the device or with the application program. If you need to change the default settings of the serial or parallel port (e. address, interrupt), you can do so in the BIOS Setup. Generate the utility and driver diskettes using the batch files in the \PROGS\DISKS directory and label them. The main switch and ON/OFF switch do not cut off power voltage from the system unit. To cut off the power supply, you must pull out the power plug. Switching the PC ready-to-operate by means of software You can put your PC into ready-to-operate mode in Windows 95 choosing Shut down in the Start menu or using the DeskOff program: Prerequisite: Your system must support switching off with software and this functionality must be enabled in BIOS-Setup (Soft Power OFF - Enabled). Switching on the PC Switch on the monitor (see the Operating Manual of the monitor). Use the main switch on the rear of system unit to switch the system unit on. Exit MS-Windows (choosing Shut down in the Start menu). The PC switches to the mode which was active when it was last switched off: If the Power ON display on the front of the system unit lights up orange, press the ON/OFF switch on the front of the system unit. The Power ON display lights up green, and the PC is started. 24 The system unit is ready-to-operate, and the the Power ON display lights up orange. A26361-K407-Z111-2-7619 A26361-K407-Z111-2-7619 25 Preparation for use and operation Connecting a MIDI Connecting a MIDI Preparation for use and operation Connecting a MIDI i You need a Game/MIDI port and a commercially available MIDI interface box or Soundblaster-compatible MIDI adapter cable. Connect the Game/MIDI port to the MIDI interface box. Connect the MIDI output of your keyboard to the MIDI input of the MIDI interface box. Connect the MIDI input of your keyboard to the MIDI output of the MIDI interface box. Switch on the device. Recording a MIDI file Press the Record button. Save the MIDI file with File - Save. Playing back a MIDI file Press the Play button. You must now also change the basic configuration of your system accordingly. Enable the MIDI interface with: Start - Settings - Control Panel - System iconDevice-Manager index tab. [. . . ] Take the drive completely out of its location (3). Press the drive cover into place until it engages. 58 A26361-K407-Z111-2-7619 A26361-K407-Z111-2-7619 59 System expansions Installing and removing drives Installing and removing drives System expansions Changing the floppy disk drive Remove the bottom cover (see "Installing and removing boards"). Pull the Game/Midi connector from the system board (see the Technical Manual of the system board). 1 2 1 Remove the screws that fix the floppy disk drive to the carrier (1) and take the drive out of the carrier (2). 2 Pull all cable connectors from the floppy disk drive. 2 1 2 1 3 Place the new floppy disk drive in the carrier (1) and fasten it using the screws you removed earlier (2). 60 Remove the screw (1). Take the carrier out of the housing (2 + 3). A26361-K407-Z111-2-7619 A26361-K407-Z111-2-7619 61 System expansions Installing and removing drives 2 3 1 a b c Put the floppy disk drive and the carrier back into the housing (1+2). Ensure that the drive carrier is secured at positions a, b and c in the housing. [. . . ]