User manual FUJITSU E8110

[. . . ] E8110. book Page 1 Tuesday, February 28, 2006 2:59 PM Fujitsu LifeBook E8110 Notebook ® User's Guide E8110. book Page 2 Tuesday, February 28, 2006 2:59 PM E8110. book Page 3 Tuesday, February 28, 2006 2:59 PM Copyright Copyright and Trademark Information Fujitsu Computer Systems Corporation has made every effort to ensure the accuracy and completeness of this document; however, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes. Fujitsu, the Fujitsu logo, and LifeBook are registered trademarks of Fujitsu Limited. Centrino, Intel, and Intel Core are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. [. . . ] Your system display won't turn on when the system is turned on or when the system has resumed. The Built-in Display has bright or dark spots. The system may be passwordprotected. A foreign object, such as a paper clip, is stuck between the display and the keyboard. If the spots are very tiny and few in number, this is normal for a large LCD display. If the spots are numerous or large enough to interfere with your operation needs. This is normal; do nothing. Display is faulty; contact your support representative. The application display uses only a portion of your screen and is surrounded by a dark frame. You are running an application that does not support 800 x 600/1024 x 768 pixel resolution display and display compression is enabled. Display compression gives a clearer but smaller display for applications that do not support 800 x 600/1024 x 768 pixel resolution. You can fill the screen but have less resolution by changing display compression settings, (See Video Features submenu located within the Advanced menu of the BIOS. (See BIOS Setup Utility on page 29 for more information) Press [Fn] + [F7] to increase brightness or doubleclick on the battery gauge and adjust Power Control under battery settings. Toggle the video destination by pressing [Fn]+ [F10] together, or check your BIOS setup and enable your external monitor. (See the Video Features submenu, located within the Advanced Menu of the BIOS. (See BIOS Setup Utility on page 29 for more information) The Display is dark when on battery power. You have connected an external monitor and it does not display any information. The Power Management utility default is set on low brightness to conserve power. Your BIOS setup is not set to enable your external monitor. 58 E8110. book Page 59 Tuesday, February 28, 2006 2:59 PM Troubleshooting Problem Possible Cause Possible Solutions You have connected an external monitor and it does not display any information. Your external monitor is not properly installed. Your operating system is not setup with the correct software driver for that device. Your external monitor is not compatible with your LifeBook notebook. Reinstall your device. (See External Video Port on page 48 for more information) Check your device and operating system documentation and activate the proper driver. See your monitor documentation and the External Monitor Support portions of the Specifications section. (See Specifications on page 73 for more information) You have connected an external monitor and it does not come on. Miscellaneous Problems An error message is displayed on the screen during the operation of an application. Application software often has its own set of error message displays. See your application manual and help displays screens for more information. Not all messages are errors some may simply be status. 59 E8110. book Page 60 Tuesday, February 28, 2006 2:59 PM LifeBook E8000 Notebook POWER ON SELF TEST MESSAGES The following is an alphabetic list of error-and-status messages that Phoenix BIOS and/or your operating system can generate and an explanation of each message. If an error message is displayed that is not in this list, write it down and check your operating system documentation both on screen and in the manual. If you can find no reference to the message and its meaning is not clear, contact your support representative for assistance. nnnn Cache SRAM Passed Where nnnn is the amount of system cache in kilobytes success-fully tested by the Power On Self Test. [. . . ] Expand Local Policies, expand Security Options, and double-click Accounts: Limit local account use of blank passwords to console login only. Dialog appears after OmniPass authentication during Windows Logon After installing OmniPass on your system, you can choose to logon to Windows using OmniPass. You authenticate with OmniPass (via master password, or an enrolled security device) and OmniPass logs you into Windows. You may, during this OmniPass authentication, see a Login Error dialog box. [. . . ]