User manual FUJITSU E8210

[. . . ] E8210. book Page 1 Friday, March 10, 2006 4:33 PM Fujitsu LifeBook E8210 Notebook ® User's Guide E8210. book Page 2 Friday, March 10, 2006 4:33 PM E8210. book Page 3 Friday, March 10, 2006 4:33 PM Copyright Copyright and Trademark Information Fujitsu Computer Systems Corporation has made every effort to ensure the accuracy and completeness of this document; however, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes. Fujitsu, the Fujitsu logo, and LifeBook are registered trademarks of Fujitsu Limited. Centrino, Intel, and Intel Core are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. [. . . ] Your BIOS setup is not set to enable your external monitor. Press [Fn] + [F7] to increase brightness or double-click on the battery gauge and adjust Power Control under battery settings. Toggle the video destination by pressing [Fn]+ [F10] together, or check your BIOS setup and enable your external monitor. (See the Video Features submenu, located within the Advanced Menu of the BIOS. (See BIOS Setup Utility on page 29 for more information) Reinstall your device. (See External Video Port on page 47 for more information) Check your device and operating system documentation and activate the proper driver. You have connected an external monitor and it does not display any information. You have connected an external monitor and it does not display any information. Your external monitor is not properly installed. Your operating system is not setup with the correct software driver for that device. Your external monitor is not compatible with your LifeBook notebook. You have connected an external monitor and it does not come on. Miscellaneous Problems An error message is displayed on the screen during the operation of an application. See your monitor documentation and the External Monitor Support portions of the Specifications section. (See Specifications on page 73 for more information) Application software often has its own set of error message displays. See your application manual and help displays screens for more information. Not all messages are errors some may simply be status. 59 E8210. book Page 60 Friday, March 10, 2006 4:33 PM LifeBook E8000 Notebook POWER ON SELF TEST MESSAGES The following is an alphabetic list of error-and-status messages that Phoenix BIOS and/or your operating system can generate and an explanation of each message. If an error message is displayed that is not in this list, write it down and check your operating system documentation both on screen and in the manual. If you can find no reference to the message and its meaning is not clear, contact your support representative for assistance. nnnn Cache SRAM Passed Where nnnn is the amount of system cache in kilobytes success-fully tested by the Power On Self Test. (This can only appear if you have an SRAM PC Card installed. ) *Diskette drive A error or Diskette drive B error Drive A: or B: is present but fails the BIOS Power On Self Test diskette tests. Check to see that the drive is defined with the proper diskette type in the Setup Utility, (See BIOS Setup Utility on page 29 for more information) and that the diskette drive is installed correctly. If the disk drive is properly defined and installed, avoid using it and contact your support representative. *Extended RAM Failed at offset: nnnn Extended memory not working or not configured properly. If you have an installed memory upgrade module, verify that the module is properly installed. If it is properly installed, you may want to check your Windows Setup to be sure it is not using unavailable memory until you can contact your support representative. nnnn Extended RAM Passed Where nnnn is the amount of memory in kilobytes successfully tested. *Failing Bits: nnnn The hex number nnnn This is a map of the bits at the memory address (in System, Extended, or Shadow memory) which failed the memory test. [. . . ] Dialog appears after OmniPass authentication during Windows Logon After installing OmniPass on your system, you can choose to logon to Windows using OmniPass. You authenticate with OmniPass (via master password, or an enrolled security device) and OmniPass logs you into Windows. You may, during this OmniPass authentication, see a Login Error dialog box. This dialog box occurs when OmniPass was unable to log you into Windows with the credentials supplied (username and password). [. . . ]