User manual FUJITSU MOBILE H Operating Manual

[. . . ] Introduction Index Important notes CELSIUS Mobile H Preparing the workstation for use Working with the workstation Operating Manual Security functions Connecting external devices Settings in BIOS Setup Troubleshooting and tips Memory expansion Technical data May 2002 edition DPMS and VESA are registered trademarks of Video Electronics Standards Association. Intel is a registered trademark, Pentium and Celeron are trademarks of Intel Corporation, USA. Macrovision is a trademark of Macrovision Corporation, USA. Microsoft, MS, MS-DOS, Windows, and Windows NT are registered trademarks of Microsoft Corporation. [. . . ] Place the workstation on a flat surface. Open the LCD display panel. A26391-K124-Z100-1-7619 37 Working with the workstation Removing modules 1 2 Ê Push the slide in the direction of the arrow (1) up to the stop and hold it in place. i Ê To remove the left-hand module, push the slide to the right. To remove the right-hand module, push the slide to the left. Remove the module the direction of the arrow (2). 38 A26391-K124-Z100-1-7619 Working with the workstation Installing modules 1 2 Ê Push the slide in the direction of the arrow (1) up to the stop and hold it in place. i Ê Ê To install the left-hand module, push the slide to the right. To install the right-hand module, push the slide to the left. Position the module at the edge of the casing (2) and then press it into the workstation. Release the slide (2). A26391-K124-Z100-1-7619 39 Working with the workstation Optical drives Your workstation is fitted with a combo drive (CD-RW/DVD). ! This device contains a light-emitting diode, classified according to IEC 825-1:1993: LASER CLASS 1, and must not be opened. Thus you avoid dust contamination, scratches, bending or other damage. Protect your CDs/DVDs from dust, mechanical vibration and direct sunlight!Avoid storing a CD/DVD in areas subject to high temperatures or humidity. You may use both 8-cm and 12-cm CDs/DVDs in the optical drive. When using CDs/DVDs of poor quality vibrations and reading errors may occur. Optical drive indicator The indicator flashes when a CD/DVD is inserted. The indicator goes out when the drive is ready-to-operate. The indicator lights up when the drive is accessed. i If the indicator does not go out after the CD/DVD is inserted, and continues to flash, the CD/DVD is probably damaged or dirty. Inserting or removing a CD/DVD The workstation must be switched on. Ê Ê Ê or Push the insert/eject button. Place the CD/DVD in the drive tray with the label facing upwards. Push in the drive tray until you feel it lock into place. The drive tray will open. Ê Ê Manual removal (emergency removal) In the event of a power failure or damage to the drive it may be necessary to manually remove the CD/DVD. Ê Ê Switch off the workstation. Push a pen or a piece of wire (such as a paper clip) into the opening for manual ejection. The drive tray is unlocked. You can now pull the drive tray out of the drive. 40 A26391-K124-Z100-1-7619 Working with the workstation LS240 drive (floppy disk drive) ! i Never clean the floppy disk drive with cleaning disks. Any attempt would destroy the read/write head in the disk drive within 20 seconds. Working with floppy disks Follow the instructions supplied by the vendor of the floppy disks. 5 7 4 1 2 3 6 1= 2= 3= 4= 5= 6= 7= Insertion direction Label area Write protection tab for a 1. 44 Mbyte floppy disk Identification of a 1. 44 MB floppy disk or write protect switch on a 120 MB floppy disk Eject button for inserted floppy disks Disk is write-protected Disk is not write-protected To insert a diskette: Ê Push the floppy disk into the drive in the insertion direction (1) until it engages. The label should be facing upward. To remove a diskette: Ê Ê Ê Push the eject button (5). Protect the floppy disk against being overwritten or erased Slide the write-protect slider into position (6). The hole is now visible. Deactivate write protection Slide the write-protect slider into position (7). The hole is now covered. A26391-K124-Z100-1-7619 41 Working with the workstation 56k-Modem A modem is already installed in your workstation. The 56k modem supports all data communication applications, such as: · · · Modem operation: High-speed downloads at up to 56, 000 bit/s (V. 90). Fax mode: Transmitting and receiving at up to 14, 400 bit/s Simple country adaptation with programme The modem complies with the EU Directive 91/263/EEC (Telecommunications terminal equipment directive) and has been checked in agreement with the guideline TBR-21. The modem can be operated in the following countries: Multifrequency (MFC) dialling Belgium, Denmark, Germany, Finland, France, Greece, Great Britain, Holland, Ireland, Iceland, Italy, Luxembourg, Norway, Austria, Portugal, Sweden, Switzerland and Spain. [. . . ] The workstation will not start without memory modules, as no fixed main memory is installed. Removing and installing memory extension ! Ê Ê Ê Ê Ê Ê Please note the information provided in the "Notes on installing and removing boards and modules" section in the chapter "Important notes". Switch off the workstation and the connected peripherals. Close the LCD display of the workstation so that it locks into place. Unplug the power adapter from the mains outlet. [. . . ]