User manual FUJITSU POINT 1600

[. . . ] has made every effort to ensure the accuracy and completeness of this document; however, because ongoing development efforts are made to continually improve the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes herein. Point 1600 and Point 510 are trademarks of Fujitsu Personal Systems, Inc. IBM, IBM PC AT, and IBM PS/2 are registered trademarks of IBM Corporation. [. . . ] (This protects the battery pack from being overcharged. ) If fully discharged, the battery pack recharges to 90% in about 90 minutes. (Charging may take longer if peripherals are attached. ) You can use the pen tablet, suspend system operation, or shut down the system, without interrupting the charging process. Also, note that there is no "memory effect". You can begin charging the battery pack at any charge level. Charging the Battery Pack (While Installed in the Pen Tablet) 2-11 Removing and Installing the Battery Pack 2 The battery pack can be removed from the pen tablet and replaced with a charged battery pack. You can then charge the battery pack that you removed in the optional external battery charger. You can remove or install the battery pack while the system is Off, in Suspend mode, or connected to external power. Caution Do not remove the battery pack while the system is running unless the system is connected to an external power source such as the AC adapter. Doing so will turn off the system and can damage files used by the operating system or applications. To remove and install the battery pack, 1. (Save any important files and information in programs that you are using before shutting down the pen tablet. ) For more information, see "Suspending the System" on page 2-6 or "Shutting Down the System" on page 2-8. 2-12 Using the Point 1600 Pen Tablet 2. Slide the battery latch on the battery pack currently installed in the pen tablet to the open position as shown in Figure 2-2. Battery Pack Slide battery pack out to remove. Slide latch to open. Battery Latch Figure 2-2 Removing the Battery Pack 3. Slide the battery pack out of the pen tablet. You can now install a charged battery pack in the pen tablet and charge the battery pack that you removed in an external battery charger if one is available. See the instructions that came with your external battery charger for details. To install a battery pack in the pen tablet, slide the latch on the battery pack to the open position. Slide the battery pack into the pen tablet until it fits snugly. Slide the latch to the closed position to latch the battery pack in place. You can now start or resume the system and use the pen tablet. Conserving Battery Power A fully charged battery pack can power the Point 1600 pen tablet for about 4 hours under typical use (with power management). Your results may vary depending on how the pen tablet is configured. You can extend the life of your battery pack by conserving battery power. 2 Conserving Battery Power 2-13 Here are some suggestions for conserving battery power: · If you will not be using the pen tablet for a few minutes, put the pen tablet in Suspend mode (see "Suspending the System" on page 2-6). · If you will not be using the pen tablet for an extended period of time, such as at the end of your work day, shut down the system. · Select the low brightness setting for the screen by tapping the Brightness Hotpad (see "Using Hotpads" on page 2-10). Using Connectors and Peripheral Interfaces 2 Connectors and peripheral interfaces on the Point 1600 pen tablet allow you to connect a variety of equipment to the pen tablet, such as a microphone, headphones, keyboard, or printer. [. . . ] · Public transportation terminals where telephones are used to call taxis or to reserve lodging or rental cars. · In hotel and motel rooms at least ten percent of the rooms must contain hearing aid compatible telephones which will be provided to hearing impaired customers on request. DOC (Industry Canada) Compliance Notices This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set forth in the radio interference regulations of the Canadian Department of Communications. 3 Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de classe B prescrites dans le règlement sur le brouillage radioélectrique édicté par le Ministère des Communications du Canada. Notice to Users of Radios and Television This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment regulations. 3 Cet appareil numérique de la classe B respecte toutes les exigences du règlement sur le matériel brouilleur du Canada. Agency Notices A-3 Notice to Users of the Canadian Telephone Network 3 The Canadian Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction. [. . . ]