User manual FUNAI ST4819

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The caution marking is located on the rear of the cabinet. IMPORTANT SAFEGUARDS 1. Read instructions-All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions-The safety and operating instructions should be retained for future reference. 3. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions-All operating and use instructions should be followed. [. . . ] NOTE: Zero Return WILL NOT work on a blank tape or a blank portion of a tape. · This function will not operate in recording mode. · This function is not operative when a cassette tape is not inserted in the TV/DVD/VHS. In the example below: To watch a program after 2 hour 50 minutes from the present position, in either direction. 1 2 Insert a tape. Select "TIME SEARCH" mode - TV/VCR SETUP TIMER PROGRAMMING SETTING CLOCK CHANNEL SET UP USER'S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN B TIME SEARCH INDEX SEARCH 1 Stop a tape at your desired point Rewind or fast forward the tape to the beginning point at which you want to review. 2 3 Reset the counter to 0:00:00 Press the COUNTER RESET button repeatedly. Begin recording or playback Press the SETUP button on the remote control. Press the Arrow K or L button to point to "TIME SEARCH". Then, press the Arrow B button. 3 Enter your desired time TIME SEARCH 2 : 50 Press the RECORD or PLAY button. Press the STOP button when recording or playback is completed. 4 To activate "ZERO RETURN" mode - TV/VCR SETUP TIMER PROGRAMMING SETTING CLOCK CHANNEL SET UP USER'S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] B ZERO RETURN TIME SEARCH INDEX SEARCH Press the SETUP button on the remote control. Press the Arrow K or L button to point to "ZERO RETURN". The counter will appear on the TV screen. The tape will automatically stop when the counter returns to 0:00:00. Press the Arrow K or L button until your desired time appears. (Example: "2:50" stands for 2 hours 50 minutes) If you wish to cancel the Time Search at this point, press the SETUP button on the remote control. 4 Begin Time Search By pressing the Arrow s or B button, the TV/DVD/VHS will rewind or fast forward to the specified point. This function is operative when Repeat Play is set to the [OFF] position. The tape will not auto-rewind during timer recording or One Touch Recording. · · - 29 - EN 1F12 RECORDING Make sure . . . · TV/DVD/VHS power must be turned on. · Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording. ) NOTES: · This unit will ONLY record and view the same channel. · This unit cannot record the contents from the built-in DVD. NORMAL RECORDING You can ONLY watch the same TV program that is being recorded. SKIPPING UNWANTED SCENES DURING RECORDING Press the PAUSE button to temporarily stop recording. Press the PAUSE or RECORD button to resume recording. NOTES: · After five minutes, the TV/DVD/VHS will automatically switch to the Recording mode to prevent tape damage. · If "CLOSED CAPTION (ON)" is selected, the OnScreen Display will appear for 5 seconds, then disappear. PAUSE SP 1 Select the channel to be recorded Press the number buttons on the CH 10 remote control or the CHANNEL K or L button. Remember: If the TV/DVD/VHS is connected to a cable box or satellite box, the TV/DVD/VHS must be on CH3 or CH4, then the channel to be recorded must be selected on the cable box or satellite box. 2 Select the tape speed Press the SPEED button to select the desired tape speed (SP/ SLP). SP 3 Begin recording REC Press the RECORD button. SP 4 Stop recording Press the STOP button when recording is completed. - 30 - EN 1F12 OTR (One Touch Recording) This function enables you to set a recording length simply by pressing the REC/OTR button on the TV/DVD/VHS. · TV/DVD/VHS power must be turned on. [. . . ] (Ejemplo: 5, PM) Luego, pulse el botón F. FWD/B. 7 Pulse el botón PLAY/K o STOP/L hasta que aparezca el minuto deseado. (Ejemplo: 40) 8 Pulse el botón SETUP en el mando a distancia. Aunque los segundos no se visualizan, éstos empiezan a contar desde 00 cuando se pulsa SETUP en el mando a distancia. Utilice esta función para sincronizar el reloj con la hora correcta. 5 El sintonizador se para en el canal memorizado más bajo. [. . . ]