User manual FUNAI T3D-D8182DB BROCHURE

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual FUNAI T3D-D8182DB. We hope that this FUNAI T3D-D8182DB user guide will be useful to you.

Lastmanuals help download the user guide FUNAI T3D-D8182DB.


Mode d'emploi FUNAI T3D-D8182DB
Download
Manual abstract: user guide FUNAI T3D-D8182DBBROCHURE

Detailed instructions for use are in the User's Guide.

[. . . ] In this case remove battery from ce cas enlever la pile caso è necessario diesem Fall Batterie aus transmitter!Release screw at the side next to the button. Draw out name plate through slot in the seal !Push in name plate with lettering and screw upper part in place. [. . . ] Release screw at the side next to the button !Drill through pre-punched areas to take screws !Guide screws through apertures and tighten carefully !When position of transmitter is being defined, please make sure that the lateral screw remains accessible! enlever le passe-câble transmitter étanche de la face arrière !Push clips on to the back de l'émetteur. Fix with the screw face arrière (partie provided inférieure). 1 with electroexistante selon figure 1 mechanical chime or avec gong ou sonnerie ringer/bell (8-12V~/=) at électromécanique terminals C and V. When installing the selon figure 2 sur les transmitter out of doors bornes 0 et C. Mode of operation: The first transmitter S1 sends the signal to the receiver E1, which in turn forwards the signal to the transmitter S2 with a short time delay. Some versions of the transmitter are equipped with a bridge on the PCB. The Alarm tone also can be set as a fixed "melody" (version GL only), see page 7 Each transmitter has an individual code so that interference from other transmitters is excluded. Up to 20 transmitters can be programmed into one receiver. However, one transmitter can be tuned to any desired number of receivers. The figure shows a few of the many possible combinations. Each receiver can be triggered individually or centrally, for example. A different melody can be allocated to each transmitter to make it possible to distinguish between them. We recommend programming transmitters and receivers before they are fixed on the wall !3 seconds until the green LED 1 goes on !The receiver plays a melody as confirmation of receipt, LED 1 goes out. [. . . ] The receiver plays a melody as confirmation of receipt, LED 1 goes out. If required, set a different melody using button T2 (see above). If no transmitter is detected, LED 1 starts to flash after approx. 10 seconds Sekunden gedrückt until the green LED 1 goes halten, bis grüne LED 1 on for a longer time zunächst länger initially and then goes aufleuchtet und dann out. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE FUNAI T3D-D8182DB

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual FUNAI T3D-D8182DB will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag