User manual FUNAI W9TVCRG

[. . . ] CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. LOCATION: INSIDE, NEAR THE DECK MECHANISM. FCC WARNING- This equipment may generate or use radio frequency energy. [. . . ] Then, press the F. FWD button. PROGRAM NUMBER 4 ONCE DAILY WEEKLY EN 1L25 ¡If a tape ends during TIMER RECORDING, the 3) Set the date First, press the PLAY button or the STOP button for the month. Next, press the PLAY button or the STOP button for the day. Then, press the F. FWD button. 4) Set the start time ONE TIME PROGRAM PROGRAM NUMBER 4 DATE --/-- -START TIME - - : - - - END TIME - - : - - - CHANNEL -REC SPEED - - First, press the PLAY button or the STOP button for the hour. Next, press the PLAY button or the STOP button for the minute. And then, press the PLAY button or the STOP button for AM or PM. Then, press the F. FWD button. 5) Set the end time ONE TIME PROGRAM PROGRAM NUMBER 4 DATE 05 /13 MON START TIME - - : - - - END TIME - - : - - - CHANNEL -REC SPEED - - Follow the same instructions as "Set the start time" to set the end time. 6) Set the channel number ONE TIME PROGRAM PROGRAM NUMBER 4 DATE 05 /13 MON START TIME 07: 30 PM END TIME - - : - - - CHANNEL -REC SPEED - - VCR will stop, eject the tape, and switch to the DVD mode automatically as the TIMER SET light blinks. (If the DVD power is off, the VCR will switch to STANDBY status). ¡If a tape is not in the VCR, or the tape does not have a safety tab, the TIMER SET light flashes and timer recording will not operate. ¡When all timer recordings are finished, the TIMER SET light will flash. To use the VCR again as usual, press the TIMER SET button to disable the flashing TIMER SET light, then press the VCR/TV button to select the VCR position. Press the VCR button to choose VCR or DVD mode, then continue with the other features as described in this manual. Then, enter correct numbers by pressing the PLAY or the STOP button. ¡You may cancel the entire program by pressing the REW button while the program number flashes. 5 Press the CLEAR/C. RESET button to exit. Press the TIMER SET button to return to timer stand-by mode. EN 1L25 for more than 30 seconds, the clock setting and all 6 timer settings will be lost. ­ 21 ­ SPECIAL FEATURES COPYING A VIDEO TAPE VCR You can make copies of video tapes made by friends or relatives for your enjoyment. Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws. Connect the recording VCR (this unit), the playing VCR (another source) and your TV using the following diagram. ¡You can use the AUDIO/VIDEO input jacks on the front panel of the VCR instead of using the jacks on the back. [Recording VCR] (this unit) DVD/VCR OUT IN ANT - IN L AUDO R ANT - OUT 3CH 4CH VIDEO R Cb DVD/VCR AUDIO OUT L Y S-VIDEO DIGITAL AUDIO OUT PCM / BITSTREAM OUT COAXIAL COMPONENT VIDEO OUT RCA-type connectors. Standard audio cables are not recommended. ¡You can use a video disc player, satellite receiver, or other audio/video component with A/V outputs in place of the playing VCR. TO MONITOR THE RECORDING 1 Turn on the TV and set the TV to channel 3 or 4. ¡Now set the CH3/CH4 switch on the back of the DVD /VCR to match the channel selected on the TV. 2 Press the VCR/TV button on the recording VCR so that the VCR/TV Light comes on. MTS (Multi-Channel Television Sound) SYSTEM VCR When you play a VHS tape, or receive a broadcast on the VCR tuner channel you are watching, the current status will appear when you press the DISPLAY button on the remote 1)* control. When you record a MTS broadcast signal, you need to set it 2)* to MTS mode. STOP 12:00AM CH 32 STEREO SAP SP 0:00:00 HIFI Cr Coaxial cable (supplied) [TV set] (Use for monitoring) Audio/Video cables (not supplied) LEFT RIGHT OUT IN VIDEO AUDIO ANT in [Playing VCR] (another source) 1)* When a program is broadcast in stereo, STEREO appears. [. . . ] 4] en la página 15 para detalles. CONECTANDO A UN DESCODIFICADOR DIGITAL DOLBY O DESCODIFICADOR DTS Por favor, vea la [Fig. 5] en la página 16 para detalles. CONECTANDO A UN AUDIO ANALÓGICO Por favor vea la [Fig. 6] en la página 16 para detalles. PREPARACIÓN PREPARACIÓN DE CANAL AUTOMÁTICA VCR 1 Conecte el TV y ponga el TV en el canal 3 ó 4. 2 Conecte el VCR presionando [POWER]. Ambas Luces POWER y VCR/TV se encenderán. 4 Inicie canal preajustado presionando [F. FWD] una vez. [. . . ]