User manual FURUNO 1834C Operators Guide

[. . . ] May also be used to enter alphanumeric data. Turning the Power On/Off Turning on the power Press the POWER/TX key momentary. Turning off the power Press and hold down the POWER/TX key until the screen goes off (approx. Press the DISP key to show the display selection window. Rotate the ENTER knob to select a basic display screen, and then push it. [. . . ] Press the GAIN key or the E: RETURN soft key to finish. 2. To erase an EBL, press appropriate EBL soft key (A or D) followed by the CLEAR key. 12/LP 3nm H-UP 319. 9°M EBL VRM A EBL1 ON VRM1 ON Adjusting the A/C SEA, RAIN 1. Press the GAIN key followed by B: A/C SEA or C: A/C RAIN soft key to show the appropriate setting window. A/C SEA AUTO ROUGH AUTO MODERATE AUTO CALM 0 MAN EBL1 (Dotted) VRM2 (Dashed) VRM1 (Dotted) EBL2 (Dashed) EBL1 B C OFFSET D EBL2 ON E VRM2 ON 330. 1°R 3. 123nm EBL2 VRM2 234. 1°R 9. 343nm EBL1 bearing/ VRM1 range VRM1 + 359. 9 °R 11. 70nm A/C RAIN 0 Active marker is highlighted. EBL2 bearing/ VRM2 range A/C SEA window A/C RAIN window 2 <PLOTTER Operation> Changing Chart Scale Press the RANGE - key (shrinks the scale, and expands image) or RANGE + key (expands the scale, and shrinks image). ROUTE NAME NEW ROUTE A 001 COMMENT PLOT B LOCAL LIST C ALPHA LIST D CONECT Entering a Mark 1. Place the cursor where you want a mark appear. 4. E CANCEL Entering a Waypoint at Own Ship Position Press the SAVE/MOB key momentarily to store your position as a waypoint. 5. 6. Press the B: LOCAL LIST or C: ALPHA LIST soft key to open the waypoint list. Use the trackball to select a waypoint, then press the A: ADD WPT soft key. Press the D: SAVE soft key to register the route, and then press the MENU key. Navigating to Waypoints Entering a Waypoint with Cursor 1. Press the MENU key, C: WAYPOINTS/ROUTES, A: WAYPOINTS and C: WAYPOINT BY CURSOR soft keys in order to show the plotter display. Operate the trackball to place the cursor where you want to enter a waypoint. Press the D: NEW WAYPOINT soft key. MARK NAME 34°44. 000'N 135°21. 000'W NEW WPT 1. 2. Operate the trackball to select a waypoint on the plotter display. Press the D: GO TO WPT soft key. Setting Arrival Alarm 1. Press the A: EDIT soft key to show the arrival alarm window. ARRIVAL ALARM 2. 3. 0 0 1 W 359. 9° PT 0. 00nm 00:00 01JAN00 359. 9° 0. 00nm v A SELECT MARK COORD TYPE v COMMENT 002WPT 02:36 01JAN01 34°44. 000'N 135°21. 000'W LAT LON B ¡ ON 0. 010nm ¤ OFF w 134° 12. 345'W 00:00 01JAN00 003WPT 34° 12. 134'N C N< - - >S E< - - >W D SAVE 4. 5. 34°44. 000'N 359. 9° 135°21. 000'W 0. 00nm PROXIMITY ALARM RADIUS 0. 00nm E RETURN 4. Press the D: SAVE soft key. 6. Use the trackball to select ON. Enter alarm range, and then press the C: ENTER soft key or ENTER knob to register setting. Press the ALARM key to finish. Creating a Route 1. [. . . ] Use the trackball to select speed desired. Press the E: RETURN soft key followed by the MENU key to close the menu. Activating Sounder Alarms 1. Press the ALARM key to show the ALARM menu. Use the trackball to select the alarm among BOTTOM, TEMPERATURE, FISH and FISH (B/L). [. . . ]