User manual FURUNO DP-6

[. . . ] Back NBDP TERMINAL DP-6 www. furuno. co. jp The paper used in this manual is elemental chlorine free. FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN Telephone : +81-(0)798-65-2111 Fax : +81-(0)798-65-4200 All rights reserved. Printed in Japan A : FEB . OME-56100-K4 (TATA ) DP-6 *00080790911* *00080790911* *00080790911* i ii TABLE OF CONTENTS FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RADIOTELEX COMMUNICATION 1. 1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1. 2 Code Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1. 3 ARQ Mode (A-Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 1. 4 FEC Mode (B-Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 2. [. . . ] 1234 8765. 00 8965. 00 1234 8765. 00 8965. 00 1234 8765. 00 8965. 00 Station name CHOUSHI-8M CHOUSHI-8M CHOUSHI-8M Figure 4-10 Log file Printing the Log File 1. Press function key [F1] and then the [7] key. Select Log File and press the [Enter] key. TRANSMISSION, RECEPTION This chapter shows you how to transmit and receive Telex messages. Also included are the procedures for frequency scanning, and automatic operation. 5. 1 Manual Calling The simplest way to communicate with a Telex subscriber is Manual Calling. For the ARQ mode, you may display beforehand the message to send or type message manually. Press function key [F3] to display the Operate menu. Operate 1: Call Station 2: Macro Operation 3: File to Send 4: Cancel Sending 5: Scan (Start/Stop) 6: Manual Reception 7: Timer Operation 8: High Tension ON 9: Manual Calling 0: Set Frequency Figure 5-1 Operate menu 2. The Set Frequency screen appears. Set Frequency Tx Freq: 0. 00 RX Freq: 0. 00 Figure 5-2 Set frequency screen 5-1 3. This can only be done with FURUNO transceivers. For other makes of transceiver, set a frequency pair at the transceiver. Press function key [F3] again and then the [9] key. The following screen appears. Manual Calling Mode : ARQ FEC ID : Figure 5-3 Manual calling screen 6. Press the [ ] key and input party's ID number. Press the [Enter] key to connect the communication line. Then, the line will be connected a short while. For ARQ mode, follow the next procedure. For FEC mode, type your message and go to step 13. The party's answerback code appears on the screen. Note: Step 9 and 10 are needed for ship to ship calling only. 10. You ship's answerback code is sent to the party. Press the [Enter] key and type your message. If you want to the party's response, press function key [F9] (Over). Press function key [F10] to disconnect the line. 5-2 5. 2 Calling a Station 1. [. . . ] Checksum NOTE Positioning system Mode indicator: A = Autonomous D = Differential E = Estimated (dead reckoning) M = Manual input S = Simulator N = Data not valid The Mode indicator field supplements the Status field. The Status field shall be set to V=invalid for all values of Operating Mode except for A=Autonomous and D=Differential. The positioning system Mode indicator and Status field shall not be null fields. AP3-2 RMA - Recommended minimum navigation information - Loran C data $--RMA, A, llll. lll, a, yyyyy. yy, a, x. x, x. x, x. x, x. x, x. x, a, a*hh<CR><LF> ||| | | | | | | | || | ||| | | | | | | | | | +------- 10 ||| | | | | | | | | +--------- 9 ||| | | | | | | +---+----------- 8 ||| | | | | | +------------------ 7 ||| | | | | +---------------------- 6 ||| | | | +-------------------------- 5 ||| | | +------------------------------ 4 ||| +----+--------------------------------- 3 | +---+-------------------------------------------- 2 +------------------------------------------------------- 1 1. Status: A=data valid, V=blink, cycle or SNR warning 2. [. . . ]