User manual FURUNO FA-30

[. . . ] www. furuno. co. jp The paper used in this manual is elemental chlorine free. FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN Telephone : +81-(0)798-65-2111 Fax : +81-(0)798-65-4200 All rights reserved. Printed in Japan A : MAY 2007 Pub. OME-44430-A (DAMI ) FA-30 *00016497010* *00016497010* *00016497010* IMPORTANT NOTICES · The descriptions in this manual are intended for readers with a solid knowledge of English. · No part of this manual may be copied or reproduced without written permission. · If this manual is lost or worn, contact your dealer about replacement. [. . . ] · There should not be more than one antenna on the same plane. The AIS VHF antenna should be mounted directly above or below the ship's primary VHF radiotelephone antenna, with no horizontal separation and with a minimum of 2. 8 meters vertical separation. If it is located on the same plane as other antennas, the distance apart should be at least 10 meters. · Install the VHF whip antenna (option) referring to the outline drawing at the back of this manual. Separate this antenna from other VHF radiotelephone antennas as shown below to prevent interference to the FA-30. Whip antenna for AIS Other VHF whip antenna More than 2. 8 m More than 10 m Horizontal separation distance More than 0. 5 m Vertical separation distance Cabling · Use coaxial cable type 5D-2V or the equivalent. · The cable should be kept as short as possible to minimize signal attenuation, and the maximum length is 50 meters. · All outdoor-installed connectors on coaxial cables should be fitted with preventive isolation such as vulcanizing tape to protect against water penetration into the antenna cable. · Coaxial cables should be installed in separate signal cable channels/tubes and at least 10 cm away from power supply cables. Crossing of cables should be done at right angles (90 degrees). The minimum bend radius of the coaxial cable should be 5 times the cable's outer diameter. 3 1. 4 Wiring Connect power source, LAN cable, VHF antenna and ground wire as shown below. VHF WHIP ANTENNA (option) AIS RECEIVER COAXIAL CABLE 5D-2V (local supply) PC, HUB, NAVNET LAN CABLE P5E-4PTX-BL (2 m or 10 m) RS-422 RATING *2 GROUND WIRE IV-1. 25sq NAVNET, SENSOR POWER CABLE (supplied) *1 12-24 VDC RED + BLACK GROUND Switchboard breaker *1 Supply from breaker on switchboard. *2 If COM lines (connection for NavNet, sensor) are not used, tape them to prevent short circuit. 4 Attaching coaxial connector (M-P-5) to coaxial cable The antenna cable (coaxial cable, type 5D-2V) is terminated at the FA-30 with an M-P-5 coaxial connector. Attach the connector to the cable as shown below. Sheath 30 mm 7 mm 2 mm Conductor Insulator Cut conductor here. Contact sleeve Solder here. Braided shield Connection of AIS viewer (FAISPC-MX) The AIS viewer may be connected to the FA-30 directly, or to both FA-30 and NavNet vx2. If change is necessary, click the Data Type drop-down list and choose data type as applicable, among the following choices. IEC61162: Transmit and receive IEC61162 format data via COM port. (P sentences are received but not transmitted. ) IEC61162+ P-sentence: Transmit and receive IEC61162+P sentences format data via COM port. With the radio buttons at RX Speed, choose how RX speed is regulated, Auto or Manual. For manual, choose speed from the drop-down list. Note: Tx speed is fixed at 38400 bps. Click "<<Port Setup" to return to the Port Setup menu. 8 NETWORK setup 9. Click Network Setup to show the Network Setup menu. 172. 031. 024. 002 255. 255. 000. 000 000. 000. 000. 000 (default=172. 031. 024. 002) 10. Enter the IP address assigned to the FA-30. 13. For NavNet connection, enter NavNet port number at NavNet Port Number. Enter ten-thousandths and one-thousandths places. 14. At Host Name, enter host name to be used in NavNet, AIS0 - AIS9. [. . . ] · Antenna or its cabling may be · Check the antenna and its cabling for damage. · Confirm the channel setting. 14 3. 4 Diagnostics The built-in diagnostic facility displays program version no. and checks RAM, ROM and RX channels for proper operation. Open Internet Explorer and show the main menu. [. . . ]