User manual FURUNO FCV-10 OPERATORS MANUAL

[. . . ] The screen you see depends on your system configuration and equipment settings. · This manual is intended for use by native speakers of English. · FURUNO will assume no responsibility for the damage caused by improper use or modification of the equipment or claims of loss of profit by a third party. · Please carefully read and follow the operation, installation and maintenance procedures set forth in this manual. [. . . ] Use or to choose screen division desired and press the ENTER key. Press the MENU/ESC key twice to close the window. WPT MARINA COMPASS True 1. 20 Menu Items HEADING True SOG: Speed over ground STW: Speed relative to water This section describes menu items not previously mentioned. For the System menu, see chapter 2. Sounder menu Sounder Pic. Advance Zoom Mode Shift Bottom Area Interference Color Erase Clutter White Line White Marker TVG Smoothing TX Power TX Rate Transducer* // [ENTER] [MENU] / : 1/1 : Bottom Lock : 0ft : Auto : 0% : 0% : 0% : Medium : On : Auto : 10 : 600W : Select : Enter : Back Graphic displays DEPTH POSITION SPEED (SOG) 1234ft SPEED (STW) 23 45. 6789N 123°45. 6789E COURSE True** ° ° 12. 3kt RNG/BRG*** TEMP 12. 3kt TRIP METER HEADING True** 123. 4 1234nm123. 4 ° ODOMETER WIND SPEED True* ° WIND DIR. True* 1234nm 1234nm 123. 4 °F 123. 4 12. 3kt BAROM PRESS TIME TO GO 123. 4 XTE ° 1234hPa 12H34M 0. 50nm * : APP or TRUE, depending on menu setting. ** : TRUE or MAG depending on menu setting. *** : To destination waypoint. *: FCV-585 only (see section 4. 10. ) Sounder menu Zoom Mode: Choose the zoom display to show among bottom lock, bottom zoom and marker zoom when "zoom" is chosen with the MODE knob. Bottom Area: Set the area where to display the bottom echo when selecting Auto mode on the RANGE key. Choose Bottom Area in the Sounder menu and press the ENTER key. Digital displays Note: When data is lost 30 sec. , the display shows "- -" at the location where data is lost. 16 1. OPERATION Bottom Area Above Below Border (above) changed to white. That color is also white on the color bar. This is useful for discriminating bottom fish from bottom. The setting range is 0 to 50 % in intervals of five. The larger the numeric, the wider the white line width. White Marker: Displays the chosen echo color in white. Choose White Marker in the Sounder menu and press the ENTER key. White Marker Color bar Choose echo color to display in white. Off / : Select [ENTER] : Set [MENU] : Cancel White Marker setting window 2. Use or to choose color desired and press the ENTER key. For example, move the arrow to the top of the color bar to display the bottom in white. The echo color chosen on the color bar is 17 1. OPERATION Display menu Display A-Scope : Off Depth Size : Small Zoom Marker : Off Temp Graph : Off Window Size : Off Battery : On Color Bar Palette : White : 64 Colors Header Info : On Nav Data1 : : Nav Data2 Fish Info : Off Fish Symbols : Off // [ENTER] [MENU] / : Select : Enter : Back Window Size: Adjust the display area of the dual frequency mode or zoom mode. Note that this function is inoperative with single frequency, nav data mode or A-Scope display. Choose Window Size in the Display menu and press the ENTER key. G:AF R:A 0 50/200 0. 0 1/1 0 20 20 Dividing line 40 40 / : Adjust [ENTER] : Set [MENU] : Cancel 60 60 49. 6 m 80 80 Display menu Depth Size: Choose the font size of the depth indication (Small, Medium or Large). [. . . ] Geographic position - latitude/longitude. Water temperature. *= Available with connection of optional sensors/navaid 36 4. INSTALLATION 4. 10 Adjustments after Installation NMEA 1. Press the MENU/ESC key to open the menu. [. . . ]