User manual FURUNO FCV-1100L

[. . . ] Back COLOR LCD SOUNDER FCV-1100L C Your Local Agent/Dealer 9-52, Ashihara -cho, Nishinomiya, Japan Telephone: Telefax: 0 7 9 8 - 6 5 - 2111 0798-65-4200 All rights reserved. Printed in Korea FIRST EDITION C2 : : AUG. O M E -2 3 6 7 0 (HIMA) F C V -1100L SAFETY INSTRUCTIONS WARNING ELECTRICAL SHOCK HAZARD Do not open the equipment. Only qualified personnel should work inside the equipment. Immediately turn off the power at the switchboard if water leaks into the equipment or something is dropped in the equipment. [. . . ] Press the [-] or [+] key to show the alarm zone setting window. 10 ft Alarm zone setting window (ex. Bottom alarm) 12. Press the [-] or [+] key to set the alarm zone. For depth alarm and temp alarm, go to step 16. Press the [-] or [+] key to show the level setting window. MIN MID MAX Level setting window 2-7 2. Press the [-] or [+] key to set the alarm level. MIN: Alarm triggered against light-blue or stronger fish echoes. MID: Alarm triggered against yellow or stronger fish echoes. MAX: Alarm triggered against red or stronger fish echoes. Rotate the [FUNCTION] switch fully counterclockwise to choose EXIT. To cancel an alarm, choose OFF at step 6, then rotate the [FUNCTION] switch to choose EXIT. Note: When multiple alarms are set, the buzzer sounds against the alarm set second (or third). 2. 4 TX/RX Menu The TX/RX menu adjusts pulse repetition rate, STC, gain, RX band, TX pulse and pulselength. DISP ALM TX/RX E/S SYSTEM *: The setting is available when MANUAL is selected at TX PULSE. PRR LEVEL : <High Frequency> STC : GAIN ADJ : RX BAND : TX PULSE : PULSE LENGTH : <Low Frequency> STC : GAIN ADJ : RX BAND : TX PULSE : PULSE LENGTH : 20 (0~20, S) 0 (0~10) +0 STD STD 0. 2 msec (0. 2~5. 0)* 0 (0~10) +0 STD STD 0. 2 msec (0. 2~5. 0)* Menu for TX/RX setting. [-/+]: Change set, [EXIT]: Exit TX/RX menu PRR LEVEL Changes pulse repetition rate. Normally, the highest rate (20) is used. When in shallow waters, second reflection echoes may appear between surface and actual bottom echo. The option "S" means the ship's speed dependent mode, where the PRR changes automatically with ship's speed. (Requires speed input. ) For further information about the ship's speed dependent mode, see page 1-19. Note: When using the transducer pair 88F-126H and 28F-24H with the PRR setting of 20, transmitter power will drop slightly on the LF/HF display when the range is within 40 m. 2-8 2. MENU OPERATION STC (High and Low Frequencies) Adjusts STC level for the high and low frequencies, and is useful for suppressing surface noise. "10" suppresses noise which is up to 5 m distance from the face of the transducer. Turn off the STC when there is no noise on the screen, otherwise weak echoes may be missed. GAIN ADJ (High and Low Frequencies) Adjusts gain of receiver unit chosen. Adjust the setting when the GAIN control cannot effectively adjust the gain. [. . . ] 1-8 DISP menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Display data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Display division . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2, A-9 DRAFT SETTING menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Dual frequency display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]