User manual FURUNO FELCOM 50 REFERENCE GUIDE

[. . . ] INMARSAT FLEET F55 SHIP EARTH STATION FELCOM 50 The paper used in this manual is elemental chlorine free. FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya 662-8580, JAPAN Telephone : Fax : 0798-65-2111 0798-65-4200 All rights reserved. Printed in Japan FIRST EDITION : MAR. OME-56480 ( TATA ) FELCOM50 *00015052512* *00015052512* *00015052512* *OME56480C20* *OME56480C20* *OME56480C20* SAFETY INSTRUCTIONS WARNING ELECTRICAL SHOCK HAZARD Do not open the equipment. Only qualified personnel should work inside the equipment. Do not approach the radome closer than 1. 6 meters when it is transmitting. [. . . ] 3 After installing the software, the settings may be transferred back to FELCOM 50 by pressing Load. 4 Clicking Restore Factory Defaults loads default FELCOM 50 configurations. Printout/storing a configuration summary: 5 Clicking Print Summary opens the Printout Viewer (see next page) which lists the settings of the end user equipment, and allows filing and/or printout. Note: Save config to a file only saves the Device Manager settings. Setting such as Net provider / Access codes / ISDN protocol are not saved. Phone book data and traffic log must be saved in the Book and Log menus. 5-34 5. CONFIGURATION FROM PC Configuration printout viewer The list is sorted by Terminal Id. Print to local printer Save to disk Terminal ld and MSN number Tyep of service Individual device settings Name/location, if entered 12 41 5-35 5. CONFIGURATION FROM PC 5. 15 Print handling setup The Printout from modem window is used for setting of default output of Traffic log, Modem configuration, etc. Clicking Configure > Print handling opens the Printout from modem window. Default print action: Normally, choose Print to screen which causes the file to be output via the Printout viewer. For an example, see "4. 6 Traffic Log Printout viewer". For direct printout, choose Print to default windows printer. Print to screen settings: Determines the output of records via the Printout viewer. Normally, use Concatenate print jobs which "chains" the jobs to be printed or saved to file. The alternative choice clears the screen after each printout. Printer settings: For hardcopy printout, make sure that the appropriate printer and font are selected. 5-36 5. CONFIGURATION FROM PC 5. 16 Ethernet interface Port configuration gets an additional tag for Telnet settings. Click Configure > Port and Telnet settings tag. If Enable access via LAN is ticked then vtLite will attempt to communicate using a raw telnet connection to the server address given in the server box. If Empty ERB access mode is also ticked then over the telnet session the vtLite will attempt to login to an Ethernet Router Board (currently no in use). If the Ethernet connection is used then the vtLite port indicator will show "LAN" rather than the port number. 5-37 5. CONFIGURATION FROM PC This page is intentionally left blank. 5-38 6. 6. 1 6. 1. 1 DATA COMMUNICATION Mobile Packet Data Service (RS-232) Introduction The Mobile Packet Data Service complies with the communication protocol defined by the Inmarsat system. The transmission data rate over the satellite link is typically 20 kbps (a 64 kbps channel is shared with other users). [. . . ] SYSTEM DESCRIPTION Calls to Mobiles See figure. The FELCOM 50 terminal receives incoming calls via the IMN phone numbers. IMN numbers are assigned to the following ports by the user: · ISDN port · RS-232 serial data port · RS-422 serial data port · USB serial data port Calls are made as ordinary international (Satellite) calls by dialing the international prefix (normally 00) followed by 870 and the IMN number, e. g. : 00 870 762420510. 870 connects the call to the dialed FELCOM 50 regardless of the Ocean Region the user currently communicates through. [. . . ]