User manual FURUNO SC-120 OPERATORS MANUAL

[. . . ] SATELLITE COMPASS SC-120 Your Local Agent/Dealer 9-52 Ashihara-cho, Nishinomiya, Japan Telephone : fax : 0798-65-2111 0798-65-4200 All rights reserved. Printed in Japan FIRST EDITION : MAR. OME-72490 ( KAMI ) SC-120 *00080919206* *00080919206* *00080919206* *OME72490P10* *OME72490P10* *OME72490P10* SAFETY INSTRUCTIONS Safety Instructions for the Operator Safety Instructions for the Installer WARNING Do not open the equipment. Only qualified personnel should work inside the equipment. Do not disassemble or modify the equipment. [. . . ] Choose item desired and press the [ENT] key. Choose ON or OFF as appropriate and press the [ENT] key. Press the [DISP] key to close the menu. OUTPUT DATA SETUP HDG OUT ?: VTG GGA ZDA GLL NMEA VER : VER 2. 0 LOG PULSE : 200p/nm HDG TALKER ID: GP OUTPUT DATA SETUP menu HDG OUT : ON : ON : ON : ON : OFF : OFF : OFF HDT HDM VTG ZDA GGA ROT VDR HDG OUT display Note 1: Some boaters may want magnetic heading when the boat is fitted with only a magnetic compass without correction of deviation and variation. HDM is obtained in this equipment by adding the magnetic variation to HDT automatically. Note 2: VBW and VHW sentences must be input at the HDG IN port to output the VDR sentence. 3-8 3. OPERATION 3. 8. 2 Navigation data Choose the data to output from the NAV OUT port as follows: 1. Choose I/O SETUP and press the [ENT] key. Choose "NAV OUT?" and press the [ENT] key. NAV OUT VTG GGA ZDA ATT GLL ROT : ON : ON : ON : OFF : ON : OFF NAV OUT menu VTG: GGA: ZDA: ATT: GLL: ROT: Course over ground and ground speed Global positioning system (GPS) fix data Time and date True heading, pitching, rolling Geographic position (latitude and longitude) Rate-of-turn data 4. Choose item desired and press the [ENT] key. OFF ON 5. Choose ON or OFF as appropriate and press the [ENT] key. Press the [DISP] key to close the menu. 3. 8. 3 Interface Normally choose IEC for supplying heading information to AIS and radars. If you are unsure of the version your equipment uses, try all three and choose the one which successfully outputs data. Choose I/O SETUP and press the [ENT] key. Choose NMEA VER and press the [ENT] key. VER1. 5 VER2. 0 IEC Format selection window 4. Choose VER 1. 5 or VER 2. 0 as appropriate and press the [ENT] key. 3-9 3. OPERATION 3. 8. 4 Log pulse This equipment provides SOG (speed over ground) in high accuracy. It converts an SOG value to a closure signal and outputs at the rate of 200 or 400 pulses/nm. Choose I/O SETUP and press the [ENT] key. Choose LOG PULSE and press the [ENT] key. 200p/nm 400p/nm Log pulse rate selection window 4. Choose 200 p/nm or 400 p/nm as appropriate and press the [ENT] key. Press the [DISP] key to close the menu. 3. 8. 5 Talker identifier mnemonics Choose the heading talker ID for the output data sentence HDT and HDM as follows: 1. [. . . ] 3-12 Log pulse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10 M Maintenance battery replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 fuse replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]